Clark's Corvair Parts, Inc. - Corvair Parts Catalog - Over 12,000 parts

WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**

196

STEEL TRUNK BOTTOMS

Fix that rusted trunk - easily! These panels go up about 3" on the sides and have all the

original reinforced ribs. You'll only ﬁnd 2 slight changes from the originals.

(1) The drain hole has been stamped but not cut thru.

(2) To avoid prohibitively costly tooling small cuts are made

in the corners prior to stamping. They can easily be

welded closed during installation.

Trunk – Steel 65-69 Cars C3231A 8 lbs.

Also see FLOOR KIT – PAGE 195

65-69 Trunk Front Corners Rubber PLUG

This small plug ﬁlls the drain holes in the front corners of all 1965-69 trunks

(under the ﬁller panels). 2 required. C9991 1 oz.

65-69 REAR FILLER PANELS

These ﬁt between the battery area (and spare tire area) and the rear panel. Check yours –

probably rusted out – especially if a Convertible! These are exact replacement panels. The

Convertibles are more as they are reinforced like the originals and include the nuts for the

rear weights.

Steel Coupes & 4-Doors Convertibles

Left (Drivers) C9159 1 lb. C9161 2 lbs.

Right C9160 1 lb. C9162 2 lbs.

PANEL DISCOUNT

page 186

— Filler Panels Discontinued When Gone —

The panels above will be

discontinued when gone

(C9159, C9161, C9162 & C9160)

65-69 FRONT DOOR PILLAR PANEL

Discontinued – Not enough orders

Please Wear Gloves

Handling Panels

¡VERY SHARP!

DOOR BOTTOM PATCH PANELS STEEL

1965-69 OWNERS – Now you can repair those rusted out doors (can be used on 4-Door cars

but requires slight modiﬁcation).

Panel goes up about 5-6" from bottom (as indicated by arrows). The old panel has to be cut off. The new panel is welded

on. Tabs on the backside are folded over and welded to the backside and bottom of the door as the originals were.

BOTTOM PANEL – Left C6643DL 3 lbs.

Right C6643DR 3 lbs.

3/4 PANEL – Goes up about 2" above the "belt line". Great for bad dents or rust.

2 can go for the same weight. Weight is high due to size.

Left C6644D Discontinued

Right C6645D Discontinued

Exact replacement steel battery areas! Fits right in

where you cut the old one out! Goes down to meet

the bottom of the rear fender. 66-69 style shown.

65 is exact for 65. Both include welded nut and hole

shown. See page 80 for bolts and hold downs.

1965 Steel C3151A 5 lbs.

1966-69 Steel C3151B 5 lbs.

PANEL DISCOUNT: page 186

PANEL DISCOUNT

page 186

C9159

C9161

C9162

C9160

iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**196STEEL TRUNK BOTTOMSFix that rusted trunk - easily! These panels go up about 3" on the sides and have all the original reinforced ribs. You'll only find 2 slight changes from the originals.(1) The drain hole has been stamped but not cut thru.(2) To avoid prohibitively costly tooling small cuts are made in the corners prior to stamping. They can easily be welded closed during installation. Trunk - Steel 65-69 Cars C3231A 8 lbs. Also see FLOOR KIT - PAGE 19565-69 Trunk Front Corners Rubber PLUGThis small plug fills the drain holes in the front corners of all 1965-69 trunks (under the filler panels). 2 required. C9991 1 oz.65-69 REAR FILLER PANELSThese fit between the battery area (and spare tire area) and the rear panel. Check yours - probably rusted out - especially if a Convertible! These are exact replacement panels. The Convertibles are more as they are reinforced like the originals and include the nuts for the rear weights. Steel Coupes & 4-Doors Convertibles Left (Drivers) C9159 1 lb. C9161 2 lbs. Right C9160 1 lb. C9162 2 lbs.PANEL DISCOUNTpage 186-- Filler Panels Discontinued When Gone --The panels above will be discontinued when gone(C9159, C9161, C9162 & C9160)65-69 FRONT DOOR PILLAR PANELDiscontinued - Not enough orders Please Wear Gloves Handling Panels ?VERY SHARP!DOOR BOTTOM PATCH PANELS STEEL1965-69 OWNERS - Now you can repair those rusted out doors (can be used on 4-Door cars but requires slight modification).Panel goes up about 5-6" from bottom (as indicated by arrows). The old panel has to be cut off. The new panel is welded on. Tabs on the backside are folded over and welded to the backside and bottom of the door as the originals were. BOTTOM PANEL - Left C6643DL 3 lbs. Right C6643DR 3 lbs. 3/4 PANEL - Goes up about 2" above the "belt line". Great for bad dents or rust. 2 can go for the same weight. Weight is high due to size. Left C6644D Discontinued Right C6645D DiscontinuedExact replacement steel battery areas! Fits right in where you cut the old one out! Goes down to meet the bottom of the rear fender. 66-69 style shown. 65 is exact for 65. Both include welded nut and hole shown. See page 80 for bolts and hold downs. 1965 Steel C3151A 5 lbs. 1966-69 Steel C3151B 5 lbs. PANEL DISCOUNT: page 186PANEL DISCOUNTpage 186C9159C9161C9162C9160