Clark's Corvair Parts, Inc. - Corvair Parts Catalog - Over 12,000 parts

WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**

Please Wear Gloves

Handling Panels

! VERY SHARP !

193

'65-69 CAR BODY PANELS

GAS FILLER POCKET – STEEL 1965-69 Reproduction

Goes inside left front fender.

C4272 2 lbs.

SEAL – GAS TANK FILLER

1961-69 Large round rubber seal that goes around neck and seals to body.

C536R 6 oz.

TOP FENDER PATCH PANELS

1965-69 FIBERGLASS Top of fender where it joins the windshield pillar and usually rusts.

Right side is where antenna usually is. Left side is corresponding area

on drivers side.

Panel is about 10" x 6" Left Side C6709 2 lbs.

Right Side C2554 2 lbs.

Not suggested for Convertibles.

1965-69 New Lower Steel

Windshield Panel

Note: This is a difﬁcult panel to replace. The windshield must be removed and these stop about 2" from the left

and right end of the windshield because that area was originally part of the fenders.

STEEL REPRODUCTION

This is all new tooling with exact detail and all die cut edges. 1965-69 exact replacement

of the original.

STEEL C641XR 5 lbs.

SUGGESTED CLIPS – For trim on ﬁberglass panel C640X – page 209

WINDSHIELD REMOVAL & INSTALLATION SUPPLIES – See pages 207-209

WINDSHIELD PILLARS – OUTER

1965-69 FIBERGLASS Join from bottom windshield panel and extends approximately 20"

up windshield pillar where they usually rust. Extends from under stainless

windshield trim to side of pillar and about 2" into top of front fender.

Left C3734 2 lbs.

Right C3733 2 lbs.

STEEL ROCKER PANELS

ALL '65-69

EXACT PROFILE Steel Rocker Panels

These are NOT "SLIP" on. Your old one must be cut out for a correct weld in replacement. Come in 40" lengths.

Get 2 to do a full side. Goes from the seam hanging down at the bottom and weld under the door sill. COUPE and

4-DOOR were originally 16 GA, but the CONVERTIBLE are stronger 12 gauge & work ﬁne for all models.

COUPE, CONVERTIBLE & 4-DOOR – 12GA C3350CT 16 lbs. ea. (2 needed per side)

Support Body

During Installation

PANEL DISCOUNT

page 186

RUBBER ROCKER PANEL DRAIN FLAP

65-69 C856 2 oz.

C856

iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**Please Wear Gloves Handling Panels! VERY SHARP !193'65-69 CAR BODY PANELSGAS FILLER POCKET - STEEL 1965-69 Reproduction Goes inside left front fender. C4272 2 lbs. SEAL - GAS TANK FILLER 1961-69 Large round rubber seal that goes around neck and seals to body. C536R 6 oz.TOP FENDER PATCH PANELS 1965-69 FIBERGLASS Top of fender where it joins the windshield pillar and usually rusts. Right side is where antenna usually is. Left side is corresponding area on drivers side. Panel is about 10" x 6" Left Side C6709 2 lbs. Right Side C2554 2 lbs. Not suggested for Convertibles.1965-69 New Lower SteelWindshield PanelNote: This is a difficult panel to replace. The windshield must be removed and these stop about 2" from the left and right end of the windshield because that area was originally part of the fenders.STEEL REPRODUCTIONThis is all new tooling with exact detail and all die cut edges. 1965-69 exact replacement of the original. STEEL C641XR 5 lbs. SUGGESTED CLIPS - For trim on fiberglass panel C640X - page 209WINDSHIELD REMOVAL & INSTALLATION SUPPLIES - See pages 207-209WINDSHIELD PILLARS - OUTER 1965-69 FIBERGLASS Join from bottom windshield panel and extends approximately 20" up windshield pillar where they usually rust. Extends from under stainless windshield trim to side of pillar and about 2" into top of front fender. Left C3734 2 lbs. Right C3733 2 lbs.STEEL ROCKER PANELS ALL '65-69EXACT PROFILE Steel Rocker PanelsThese are NOT "SLIP" on. Your old one must be cut out for a correct weld in replacement. Come in 40" lengths. Get 2 to do a full side. Goes from the seam hanging down at the bottom and weld under the door sill. COUPE and 4-DOOR were originally 16 GA, but the CONVERTIBLE are stronger 12 gauge & work fine for all models. COUPE, CONVERTIBLE & 4-DOOR - 12GA C3350CT 16 lbs. ea. (2 needed per side)Support Body During InstallationPANEL DISCOUNTpage 186RUBBER ROCKER PANEL DRAIN FLAP 65-69 C856 2 oz.C856