Home | Order Catalog | Online Catalog | New Items | Contact Us |
|
![]() |
|
![]() |
|
![]() |
![]() |
![]() |
|
![]() |
![]() i WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov** 181 ENGINE BOLTS SHROUD BOLTS – ALL YEAR CORVAIRS – Order extras so you have them when needed. 1/4" DIAMETER WASHER HEAD: Plated, used in several places on the top shroud and lower thermostat shroud, muffler heat shields (sold Set of 10) C2121 6 oz./set 3/8" LARGE WASHER HEAD BOLT: Used for edges of top shroud. Holds heater hose ducts to heads and other shrouds at other end of heads, plated. (Sold Set of 10) C2122 8 oz./set WASHER HEAD SHEET SCREW: (2) sizes used on most engines in various places for shrouds (upper and lower) (Sold Set of 10) Smaller Original Size (#8) Screws C2124A 2 oz./set Larger Original Size (#10) Screws C2124 2 oz./set OVERSIZE FOR STRIPPED ORIGINALS: lf Original Size is C2124A – for OVERSIZE, USE C2124 2 oz./set If Original Size is C2124 – for OVERSIZE, USE (#12 screws) C2125 2 oz./set CLIPS FOR SHEET METAL: Used in several places on rear shrouds, below oil cooler, etc. 1960-69 – Gives you something to "screw into”. Available in 2 sizes – Larger usually for front & rear shroud retainers (60-64). "1" = Set of 10 (both for #10 screws) 5/8" x 7/16" C2128 2 oz. 3/4" x 1/2" C2128L 2 oz. HEX HEAD WASHER: Self tapping – MACHINE SCREW – This is it! The one you lose and then try to force in a sheet metal screw. This is used in numerous places, go into little nuts welded to shrouds, also those 3 where heater hose adaptor attaches to shroud. (Sold Set of 10) Original Size: C2126 2 oz./set Oversize: C2127 2 oz./set SHROUD BOLTS – mixed: Set of 21. 3 of each bolt and screw. (including oversize) listed above. Gives you a good selection but is NOT ENOUGH for a full engine. Order 3-4 sets. C6171 6 oz./set Stainless Pre-formed Staples: Original size, easier to use than wire. Re-drill the holes (through the rubber seal) with a #53 drill (.007) bigger, but staple goes in easier) or #54 (.003 bigger than original holes). 1 set of 15 does 1 side, 50 for full engine. Set of 50: C858E 2 oz. Drills: #53 = C858B #54 = C858C 1 oz. "E & F" FRONT & REAR ENGINE SEAL SCREWS & RETAINERS Original style screw heads & retainers fit 61-64 Cars & 61-65 FC engine rubber seal retainer. Sold as set of 6 (some take 5; some take 6). FRONT: 61-64 Cars & 61-65 FC (#10 Screws & Retainers) E & F =set/ 6 of each C2129R 2 oz. Set/10 Screws (F) only – C11689 2 oz. Set/10 Retainers (E) only – C2128L 2 oz. 2 oz. REAR: 61-64 Cars (#10 Screws & Retainers) E & F = set/6 of ea. C2129X 2 oz. Set/10 Screws (F) only – C11689 2 oz. Set/10 Retainers (E) only – C2128 2 oz. 61-65 FC (#10 Screws & Retainers) E & F =set/ 6 of ea. C2129R 2 oz. Set/10 Screws (F) only – C11689 2 oz. Set/10 Retainers (E) only – C2128L 2 oz. Oversized Screws: Set/5 (front or rear) – C11690 2 oz. ENGINE SEAL RETAINER SCREWS 1965 Screws: Most were not "top hat" style. These are a good repro (black oxide like the originals), screw and small washer. Individual Screw C3400C ½ oz. ea. Full Set of 28 (includes one extra) C3400CR 6 oz. 1966-69 "Top Hat" Screws: These black oxide screws were used to attach the engine rubber seal to the body. Ours are nearly exact repros, but the built in washer is slightly thinner and they do not have the small letter stamped on the top. Individual Screw C3400L ½ oz. ea. Full Set of 28 (includes one extra) C3400R 6 oz. Top Engine Cover Bolts – A MUST Special high strength zinc plated bolt with serrated washer head. These bolts will hold their torque. Top housing is common oil leak area due to stress and vibration it is subjected to. Regular bolts often loosen. Sold Set of 16 bolts. C3979 12 oz./set TOP BLOCK BOLTS & OIL FILTER ADAPTOR SET: All with serrated washer head. 1960-64: C8636E 1965-69: C8636 1 lb./set HEADNUTS - ORIGINAL STYLE These have the original style built-in "collar", (just a flat washer under a regular nut is not suggested). Although heat treated I only suggest using them once. For All Corvairs. HEADNUTS – PLATED: Set of 12 C1089 6 oz./set (1/2 Set) – Set of 6 C4633 4 oz./set CHROME ACORN NUTS: Install after the head nuts to keep the ends of the studs from rusting (for upper studs). Set of 12 acorn nuts – C3413 6 oz./set All sold each. 4 oz. ea. OUR REPRO STUDS LOWER TO ROCKER ARM – Standard STUD C8247 (Shor ter) (.003) STUD C6812 (.006) STUD C6813 UPPER TO CYLINDER HEAD – Standard STUD C5260 (Longer) (.003) STUD C4293 (.006) STUD C4294 BLIND ENDED NUT: For installing and torquing engine studs (double nutting can damage threads). C2001 2 oz. C3400C C3400L ![]() |
Next![]() |
Search In Corvair Catalog Content
|
CLARKS- MORE THAN PARTS. |
![]() |
What's
New | Clark's History | Corvair
History | Contact Us | Customer
Service | Technical Service
| Change of Address
Order Catalog | Catalog Indexes | Technical Tips | Corvair Power | Engine Worksheet | Interior Worksheet | Parts We Buy | Cars, Buy or Sell Order Forms: Parts | Gift Certificates | Ordering Policies | Shipping Charges |
![]() |
![]() 400 Mohawk Trail Shelburne Falls, MA 01370 USA All rights reserved. Main Office Phone: 413.625.9776 Fax: 413.625.8498 |