i
WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**
166
This is a project that I never dreamed would happen, but thanks to your support, it
happened. Due to the size of the required order, this will probably be a one time run –
especially for the vans. The inner and outer races are made of bearing quality steel and
heat-treated to 60-64 HRC. The barrel rollers are forged, precision ground and heat-
treated to 60-64 HRC. These parts are designed to fit and work in your old axle housing
including 60-62 cars or 61-65 FC stamped steel and 63-64 cars cast iron. You can also
buy some of the parts separately. It is easy to rebuild once the bearing is off, or you can
send your axle and bearing to us and we will do everything (see below).
REBUILD KIT: You get (1) completely assembled bearing unit (photo #1). Includes 2
side seals, pulling ring, rivets & O-rings (as needed); enough for 1 bearing. We also
include shims, special synthetic grease and instructions. We also offer the kit with metal
"mushroom" deflector. 63-64 owners – see complete units below.
KIT WITH PULLER RING KIT WITH PULLER RING & MUSHROOM
60-62 Car C6680P 1 lb. 8 oz. C6680PM 1 lb. 10 oz.
63-64 Car C6684P 1 lb. 8 oz. C6684PM 1 lb. 10 oz.
61-65 FC C6687VP 1 lb. 11 oz. - - - - - - - -
SEPARATE PARTS FOR CARS & FC: We Suggest Kits Above.
60-62 Cars for Stamped Steel Housing Bearing Unit – assembled (photo #1) C11750 1 lb.
Set of 2 Seals for 1 bearing C11740 2 oz.
Set of 2 O-Rings for 2 bearings C11741 1 oz.
Set of Rivets for 2 bearings C11742 2 oz.
63-64 Cars for Cast Housing Bearing Unit – assembled (photo #1) C11750 1 lb.
Set of 2 Seals for 1 bearing C11743 2 oz.
Special Synthetic Grease for 1 brg C11743G 4 oz.
61-65 FC for Stamped Steel Housing Bearing Unit - assembled C11751 1 lb.
Set of 2 Seals for 1 bearing C11745 2 oz.
Set of O-Rings for 2 bearings C11746 1 oz.
Set of Rivets for 2 bearings C11742 2 oz.
Special Synthetic Grease for 1 brg C11743G 4 oz.
*****VAN OWNERS*****WE REALLY NEED YOUR SUPPORT! Show us there really are FC owners out there!
REBUILT AXLE BEARINGS – READY TO INSTALL OR INSTALLED!
NOTES: Bearings are completely rebuilt using our new bearing kits. All prices include a refundable core; just the housings need to be perfect to
receive a full core value. When available, we also offer the rebuilt bearing installed on a good used axle shaft (does not include the flange at the
end). To receive full core value on these, the splines must be good. 1963-64 owners – see complete units below.
REBUILT BEARING
W/ NEW PULLER RING
REBUILT BEARING W/ NEW
PULL RING & MUSHROOM
REBUILT BRG on AXLE W/ PULL RING
& USED DUST SHIELD
60-62 Car Bearing
(with stamped housing)
C713R 4 lbs. C713RPM 4 lbs. 4 oz. C9576A 14 lbs.
61-65 FC Bearing
(with stamped housing)
C1187R 4 lbs. NONE C9395A 15 lbs.
***** CORE for bearing and bearing and axle are included in prices.*****
SERVICE TO REMOVE & INSTALL AXLE BEARING(S)
This service assumes that you send us your 60-64 car or 61-65 FC axle shaft with bearing (if present). We will remove the old bearing (if present)
and install either the bearing you supply or a Bearing that you are Ordering. If the puller ring is no good or damaged, we will have to charge you
additional for that. You must pay shipping both to and from Clark's. Labor Cost to Remove & Install Bearing (no dust shield) C11769 14 lbs.
Labor Cost to Remove & Install Bearing (with dust shield) C11770 14 lbs.
REPRO AXLE BEARINGS for 60-64 CARS & 61-65 FC
FC bearings – Will probably not
be re-run. Please order now if you
think you are going to need them.
"mushroom"
Complete – New – In Stock!
1963-64 Car Complete Axle Bearings
All new & ready to install. The old bearing castings often break when removing or are
worn where the bearing races ride. We start with all new castings & parts inside.
No cores to return! Only fit 1963-64 cars. Completely assembled.
Complete bearing unit with pulling ring C714N 4 lbs.
Complete bearing unit w/ pulling ring & metal "mushroom" deflector C714NM 5 lbs.
New axle bearing on used axle shaft w/ puller ring & used dust shield (core value is only for
the axle shaft, but you may return it with the old bearing on it.)
C9577N 14 lbs.
1963-64: This large clip holds everything inside the cast housing.
Comes in complete units. C1203 2 oz.
C1203
Prev 
