Clark's Corvair Parts, Inc. - Corvair Parts Catalog - Over 12,000 parts

WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**

163

1965-69 REAR SUSPENSION

PICTURE #

½. BOLTS – BRACKET TO BODY: "1" = 2 bolts & 2 flat washers – 2 Sets needed per side “Gr 8” C2165 4 oz./set

1. BRACKET – ARM TO BODY C4596 Discontinued

2. BOLT – TORQUE ARM TO BRACKET: "Gr 8" suggested – Sold as 1 bolt, lock washer, nut. "Gr 8" C3160 6 oz./set

3. NUTS – "STABILIZING ROD": 4 per rod used – 2 rods per car – Sold Sets of 4 nuts. Steel C4597 2 oz./set

Stainless Steel C4598 2 oz./set

4. SPECIAL WASHERS: Hold bushings on. 4 needed per rod – 2 rods per car. Original, Sold each. C395 2 oz.

Non-Original Style $ Saver Washer C395X 2 oz.

C395 will give you the original washer with the stamped "locking hex" and is what is included in all of our kits.

C395X will save you $$ and works but does not have the "locking hex" & is smaller diameter than original.

5. BUSHINGS: 4 needed per rod – 2 rods per car. INDIVIDUALLY: C396 2 oz. ea. SET OF 4: C376 6 oz./set

5½. 1965-69 REAR "STABILIZING ROD" BUSHING, WASHER, NUT SET

4 rubber bushings, 4 original steel washers & 2 stainless nuts to do 1 side.

Note: some of these parts are also available in some of our rear suspension

Multi-Kits, so be careful not to double order. C2560 8 oz.

6. "STABILIZING ROD": Attaches near the front of transmission.

8. BOLTS – BRACKET TO CROSSMEMBER: "Gr 5" C2170A 4 oz.

8½.

BUSHING: REAR CROSSMEMBER – Above and in front of transmission. 2 needed.

C2050 8 oz.

BOLTS: Goes thru bushing - "Gr 8" C2169 4 oz.

BOLTS – BRACKET (8 3/4) to BODY: Either side – 2 sets needed. (Set = 2B, 2FW, 2LW, 2N) "Gr 8 " C2167 6 oz./set

BOLTS – OUTER STRUT ADJUSTING: For camber adjusting. These are usually very rusty.

I suggest you get the complete bolt unit. Torque 85-95 Ft. lbs.

Individual parts: See #10, #11, #12, #13

COMPLETE BOLT UNIT: For 1 side (as shown) C638A 8 oz.

BOLT UNIT: Less 2 special washers that fit into bushing. C638 6 oz.

BOLT ONLY C4599 4 oz.

10. SPECIAL WASHERS: Fit inside bushing. A MUST! (See also #9) Each C638X 1 oz.

Set of 4 C638W 4 oz./set

11. WASHER: Adjusting (Hole is off center) – (See also #9) C4600 2 oz.

12. LOCK WASHER "Gr 8" C4601 2 oz.

13. SPECIAL NUT – "GR 8": Don’t use anything else! CORRECT LENGTH C4602R 2 oz.

14.

REBUILT STRUT RODS - 65-69

Rod is sandblasted, painted and (2) new bushings with serrated sleeves

are installed. The rubber bushings are professionally vulcanized to the sleeve – just like the factory ones. The nylon bushings are the ones we’ve sold since the mid-80's. We

also offer rods with Nylon on the Inner End & Molded Rubber on the Outer End. This is a good combination. The nylon is unaffected by gear oil and stiffens the control.

The rubber at the outer end keeps it from being as stiff as if it had nylon on both ends. The rubber ends are our bushings that are molded like the originals. Your old strut

has a REFUNDABLE CORE VALUE IF NOT PHYSICALLY DAMAGED. Also consider bolts – #9 & page 164 #16.

REBUILT ROD w/ RUBBER BUSHINGS REBUILT ROD w/ NYLON BUSHINGS REBUILT ROD w/ 1 NYLON & 1 RUBBER END

C8235 8 lbs./rod C8236 8 lbs./rod C11735 8 lbs./rod

Heim Joint Strut Rods

REAR LOWER STRUT RODS: Heavy duty non-greaseable joints.

EXACT replace ments for original rods, provide the ultimate for accurate

adjustment and control of rear suspension. Sold each, but must be installed on both sides.

These use the original style bolts. We SUGGEST NEW BOLTS #9 ABOVE C638 and PAGE 164 #16 C4605.

C5702 5 lbs. ea.

REPLACEMENT ENDS: LEFT hand threads C6888 1 lb.

RIGHT hand threads (like "regular" threads) C6889 1 lb.

REPRODUCED STEEL: LEFT C374R 12 oz.

(Longer One) RIGHT C375R 1 lb.

STAINLESS STEEL: LEFT C1498 12 oz.

RIGHT C1499 1 lb.

See #5½

C4602R

Pg. 125

C395

C2050

C638A

iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**1631965-69 REAR SUSPENSIONPICTURE # 1/2 . BOLTS - BRACKET TO BODY: "1" = 2 bolts & 2 flat washers - 2 Sets needed per side "Gr 8" C2165 4 oz./set1. BRACKET - ARM TO BODY C4596 Discontinued 2. BOLT - TORQUE ARM TO BRACKET: "Gr 8" suggested - Sold as 1 bolt, lock washer, nut. "Gr 8" C3160 6 oz./set3. NUTS - "STABILIZING ROD": 4 per rod used - 2 rods per car - Sold Sets of 4 nuts. Steel C4597 2 oz./set Stainless Steel C4598 2 oz./set4. SPECIAL WASHERS: Hold bushings on. 4 needed per rod - 2 rods per car. Original, Sold each. C395 2 oz. Non-Original Style $ Saver Washer C395X 2 oz. C395 will give you the original washer with the stamped "locking hex" and is what is included in all of our kits. C395X will save you $$ and works but does not have the "locking hex" & is smaller diameter than original.5. BUSHINGS: 4 needed per rod - 2 rods per car. INDIVIDUALLY: C396 2 oz. ea. SET OF 4: C376 6 oz./set 5 1/2 . 1965-69 REAR "STABILIZING ROD" BUSHING, WASHER, NUT SET 4 rubber bushings, 4 original steel washers & 2 stainless nuts to do 1 side. Note: some of these parts are also available in some of our rear suspension Multi-Kits, so be careful not to double order. C2560 8 oz.6. "STABILIZING ROD": Attaches near the front of transmission.8. BOLTS - BRACKET TO CROSSMEMBER: "Gr 5" C2170A 4 oz.8 1/2 . BUSHING: REAR CROSSMEMBER - Above and in front of transmission. 2 needed. C2050 8 oz. BOLTS: Goes thru bushing - "Gr 8" C2169 4 oz. BOLTS - BRACKET (8 3/4) to BODY: Either side - 2 sets needed. (Set = 2B, 2FW, 2LW, 2N) "Gr 8 " C2167 6 oz./set9. BOLTS - OUTER STRUT ADJUSTING: For camber adjusting. These are usually very rusty. I suggest you get the complete bolt unit. Torque 85-95 Ft. lbs. Individual parts: See #10, #11, #12, #13 COMPLETE BOLT UNIT: For 1 side (as shown) C638A 8 oz. BOLT UNIT: Less 2 special washers that fit into bushing. C638 6 oz. BOLT ONLY C4599 4 oz. 10. SPECIAL WASHERS: Fit inside bushing. A MUST! (See also #9) Each C638X 1 oz. Set of 4 C638W 4 oz./set11. WASHER: Adjusting (Hole is off center) - (See also #9) C4600 2 oz.12. LOCK WASHER "Gr 8" C4601 2 oz.13. SPECIAL NUT - "GR 8": Don't use anything else! CORRECT LENGTH C4602R 2 oz.14. REBUILT STRUT RODS - 65-69Rod is sandblasted, painted and (2) new bushings with serrated sleeves are installed. The rubber bushings are professionally vulcanized to the sleeve - just like the factory ones. The nylon bushings are the ones we've sold since the mid-80's. We also offer rods with Nylon on the Inner End & Molded Rubber on the Outer End. This is a good combination. The nylon is unaffected by gear oil and stiffens the control. The rubber at the outer end keeps it from being as stiff as if it had nylon on both ends. The rubber ends are our bushings that are molded like the originals. Your old strut has a REFUNDABLE CORE VALUE IF NOT PHYSICALLY DAMAGED. Also consider bolts - #9 & page 164 #16.REBUILT ROD w/ RUBBER BUSHINGS REBUILT ROD w/ NYLON BUSHINGS REBUILT ROD w/ 1 NYLON & 1 RUBBER END C8235 8 lbs./rod C8236 8 lbs./rod C11735 8 lbs./rodHeim Joint Strut RodsREAR LOWER STRUT RODS: Heavy duty non-greaseable joints. EXACT replace ments for original rods, provide the ultimate for accurate adjustment and control of rear suspension. Sold each, but must be installed on both sides. These use the original style bolts. We SUGGEST NEW BOLTS #9 ABOVE C638 and PAGE 164 #16 C4605. C5702 5 lbs. ea.REPLACEMENT ENDS: LEFT hand threads C6888 1 lb. RIGHT hand threads (like "regular" threads) C6889 1 lb.REPRODUCED STEEL: LEFT C374R 12 oz. (Longer One) RIGHT C375R 1 lb.STAINLESS STEEL: LEFT C1498 12 oz. RIGHT C1499 1 lb.See #5 1/2 C4602RPg. 125C395C2050C638A