iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**178HEADLIGHT HARDWAREELECTRICAL CONNECTORS - see page 99SWITCHES & DIMMERS - see page 84B1. 1960-64 CARS & 61-65 FC: Plastic bracket, adjustment screw and parts to attach for adjusting. Often broken. Takes 2 per headlight bulb. C3676 4 oz.2. HEADLIGHT ADJUSTING SCREWS: 1960-64 & 1965-69. As needed. 1" C3677 1 oz. 1 1/2" C3678 1 oz.3. Some 1965-69 IF NEEDED: Headlight adjuster only used on a few cars. Most used type #4. Put in with pop rivets or small bolts (not supplied). Uses 4 per side if used. C3579 1 oz. Small bolts (enough for 1) C9262 1 oz.4. Some 1965-69 AS NEEDED: Most 1965-69 used this headlight adjuster. Most 1965 used (4) 1" per side and most 1966-69 used (3) 1" and (1) 1 1/2". 1" Screw & Plastic "Nut" C3680X 2 oz. 1 1/2" Screw & Plastic "Nut" C3680 2 oz. 1960-69 SPRING: Holds rim that holds headlight. Originals riveted on. Use small bolt and nut (not supplied). C3681 2 oz. Bolt & Nut C9261 1 oz. 1960-69 SCREW: Holds rim against headlight bulb. 2 needed per bulb. Usually in poor shape. Sold Set of 4. ORIGINAL SIZE C3682 1 oz. /set 1 SIZE OVERSIZE C3683 1 oz. /set1965-69 Headlight Stainless Trim: Holds bulb in place. NEW REPRO. Fits high & low beams. C5566H 4 oz. ea. HEADLIGHT BUCKET SCREWS: These hold the headlight "bucket" into the body opening. Sold enough for 1 bucket. 61-64 Cars : C9064 2 oz./set 1965 Cars: C9065 2 oz./set 61-65 FC: C5355A 2 oz./set 66-69 Cars: C9066 2 oz./set65-69 Trunk Headlight Screw "Covers": The 65-69 headlight buckets are held in with small sheet metal screws that stick into the trunk. Two or three on each side that were easily visible were covered by small rubber covers. Sold set/6. (slightly different from originals) C6682H 2 oz.65-69 Black Nylon Screw Covers: These are used to cover various sheet metal screws that protrude into trunk. Sold set/5. C6682C 2 oz.TAILLIGHT & BACK UP LENS SCREWS NEW AND SHINY! Oversize for stripped holes may require drilling holes slightly bigger in lens. NOTE: 1964 tail light lens screws originally were machine thread screws (C4259A, C4259). Most have been replaced by sheet metal screws (C4258A, C4258).31960-63 Cars (Set of 4) C4256A 1 oz./set (Set of 8) C4256 2 oz./set Oversize (Set of 4) C4257 1 oz./set1964 Cars (see note above) (Set of 4) C4258A 1 oz./set (Set of 8) C4258 2 oz./set Machine thread (Set of 6) C4259A 1 oz./set (Set of 12) C4259 2 oz./setSCREWS - TAILLIGHT & BACKUP UNITS TO RETAINER1960-64 Cars & 1961-65 FC (Vans): 2 screws per unit to hold them into the body (to retainer). Often very rusty (you will see them when lenses are removed). Sold set/4. 1960-64 Cars: Original Size C5090 2 oz./set 1960-64 Cars: Oversize for rusted holes C5091 2 oz./set 1961-65 FC (Vans): Original Size C4958 2 oz./setFC (VAN) TAILLIGHT RETAINER: Set of 4. Holds unit tight and grounds it. C7728 2 oz./set1965-69 Cars (Set of 6) C4259A 1 oz./set (Set of 12) C4259 2 oz./setTAIL & BACK UP LIGHT RETAINING NUTSOriginal style for 1965-69 Cars. Inside engine compartment. Set of 4 - enough for 2 light units. C5093 1 oz./set1961-65 FC (Vans) Set of 3 Screws for 1 lens. C4957 2 oz. 1961-65 FC (Vans) REAR REFLECTOR SCREWS Set/3 Original Zinc Plated Screws (enough for 1 side) C4956 1 oz. Set/6 Original Size but stainless (enough for 2 sides) C4956A 2 oz.INSTALLATION KITS - Taillight & Back-Up UnitsOther than these KITS you only need a retainer (pg. 93B) and a lens (pg. 93B) to install your taillight or back-up unit. Kit Includes: Exact repro black gasket (unit to body), lens gasket, bulb, screws for one lens to unit and screws for unit to retainer (body on backups). 1960-64 TAILLIGHT INSTALLATION KIT (for 1 unit) C7554 6 oz. 1960-64 BACKUP INSTALLATION KIT (for 1 unit) C7555 6 oz.FRONT DIRECTIONAL LENS SCREWSMay vary slightly from the original. Set of 2 - 1960-64 Cars & 1961-65 Vans C6838 1 oz./set Set of 4 - 1965-69 Cars C918 2 oz./set"SPEED" NUT FOR FRONT DIRECTIONAL UNITS: 1965-69 - Sold Set of 4 C5302 2 oz./setScrews - Station Wagon (Engine Cover, Side Covers & Differential Cover)Originally the engine & covers to each side were chrome plated and the differential cover screws were zinc plated. We are supplying stainless screws that can be buffed to look like chrome for all of these screw applications. Replace any rusted or damaged Phillips head originals. These are original truss style head with #3 phillips. Unpolished Stainless Polished StainlessEngine Cover takes 4 Type "A" screws Type "A" C3954U 1 oz. ea. C3954P 1 oz. ea.2 Side Covers take 2 Type "B" per side Type "B" C4870U 1 oz. ea. C4870P 1 oz. ea.Differential Cover takes 18 Type "B" Set 22 Type "B" C6023X 12 oz./set C6023XP 12 oz./set of 22