Home Order Catalog Online Catalog New Items Contact Us

i
WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**
82
Copper Ground Strap – Reproduced
1960–69 Small engine shroud to body "ground straps" (radio suppression).
Most use the "regular length" (6-7" overall). Some 1967-69 apparently used a "longer" (8" overall).
Regular Length: C435R 2 oz. Longer Length: C435RL 2 oz.
Ground Strap – Screw & Lockwasher Sets: Sold Set of 6 screws and lockwashers. 1960-66
(Note: 1967-69 – The Assembly Manual shows they did not use lockwashers, otherwise identical.)
Set of 6 Screws & Lockwashers (1960-66) C9685 2 oz./set
Set of 6 Screws – No Lockwashers (1967-69) C9686 2 oz./set
Voltage Regulator Ground Strap: Fits all 1965-69 – essential due to rubber regulator mount. C9657 2 oz.
1965-69 Electrical Connector: Goes on frame by battery. Small positive cable joins here.
"Always broken!" C6802 2 oz.
Screw for Center of Retainer C6827 1 oz.
Generator Parts
Generator Parts – Fit all 1960-64 unless otherwise noted
Basic Generator Rebuild Kit: Includes parts normally needed.
#1-C2782B commutator bushing, #2-C4344 brushes, #19-C618 bearing gasket, #20-C617X bearing,
#22-C619 felt washer, #23-C1222 key, #28-C4300 warning paper, C7896 stud nuts and LW. C8175 10 oz.
PICTURE # Usually MUST Be Replaced
1. Commutator End Frame: 2 styles, see diagram. All are aluminum. 1960-64. C2782 1 lb. C2783 1 lb.
Replacement Bushings: For any commutator end frame. C2782B 4 oz.
Replacement Oil Filler Caps: Commutator End STEEL: C2783C PLASTIC: C2783CP 1 oz.
Pulley End STEEL: C2783E PL ASTIC: C2783EP 1 oz.
Wick for Commutator End: 1960-64 Generator C2863 1 oz.
"Metal Freeze Plug": And gasket to seal above wick C2864 1 oz.
2. Brushes – Generator: 1960-64 Cars & FCs. 2 required. C4344 2 oz. each
3. Brush Spring C2773 1 oz.
4. Brush Pressure Arm C4345 1 oz.
5. Brush Holder: Complete Kit – insulated, includes armature terminal stud C3866 4 oz.
5½. New Armature: All New Repro. (10 1/8" doesn't fit some "SHORT" 1960). Replace your old one & be sure! C11268N 8 lbs.
6. Field Terminal Stud C3864 2 oz. (also see #28, page 83)
7. Large Screws: Side of generator, set of 2. C2861 2 oz./set
8. Field Pole Insulators: 2 needed C3889 1 oz. each
10. Bolts: 7-7/8" C2865 4 oz.
11. Bolt Lock Washers: Set of 2 C2866 1 oz./set
12. Pulley & Fan: 2-7/8" o.d. may vary from original style Discontinued
13. Wavy Washer C2774 2 oz.
14. Nut C2775A 2 oz.
15. Field Coils: NEW – Highly suggested. 1961-64 Set C3868 2 lbs./set
16. Inner Spacer C2681 1 oz.
17. Screws – Retainer : Set of 3 C3863 1 oz./set
18. Bearing Retainer C2680 Discontinued
See REBUILT GENERATORS: Bottom of page 83
VOLTAGE REGULATORS: See page 84B
SWITCH TO ALTERNATOR? See page 84A
We suggest new field coils (#15) & armatures
(#5½). The originals are old & the insulation
is deteriorating. You don't need to switch to an
alternator, you need a Clark rebuilt generator.
plastic cap
C8175
C2782
C2783
iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**82Copper Ground Strap - Reproduced1960-69 Small engine shroud to body "ground straps" (radio suppression).Most use the "regular length" (6-7" overall). Some 1967-69 apparently used a "longer" (8" overall). Regular Length: C435R 2 oz. Longer Length: C435RL 2 oz.Ground Strap - Screw & Lockwasher Sets: Sold Set of 6 screws and lockwashers. 1960-66(Note: 1967-69 - The Assembly Manual shows they did not use lockwashers, otherwise identical.) Set of 6 Screws & Lockwashers (1960-66) C9685 2 oz./set Set of 6 Screws - No Lockwashers (1967-69) C9686 2 oz./setVoltage Regulator Ground Strap: Fits all 1965-69 - essential due to rubber regulator mount. C9657 2 oz.1965-69 Electrical Connector: Goes on frame by battery. Small positive cable joins here. "Always broken!" C6802 2 oz. Screw for Center of Retainer C6827 1 oz.Generator PartsGenerator Parts - Fit all 1960-64 unless otherwise notedBasic Generator Rebuild Kit: Includes parts normally needed. #1-C2782B commutator bushing, #2-C4344 brushes, #19-C618 bearing gasket, #20-C617X bearing,#22-C619 felt washer, #23-C1222 key, #28-C4300 warning paper, C7896 stud nuts and LW. C8175 10 oz.PICTURE # ?Usually MUST Be Replaced?1. Commutator End Frame: 2 styles, see diagram. All are aluminum. 1960-64. C2782 1 lb. C2783 1 lb. ?Replacement Bushings: For any commutator end frame. C2782B 4 oz. Replacement Oil Filler Caps: Commutator End STEEL: C2783C PLASTIC: C2783CP 1 oz. Pulley End STEEL: C2783E PL ASTIC: C2783EP 1 oz. Wick for Commutator End: 1960-64 Generator C2863 1 oz. "Metal Freeze Plug": And gasket to seal above wick C2864 1 oz.?2. Brushes - Generator: 1960-64 Cars & FCs. 2 required. C4344 2 oz. each 3. Brush Spring C2773 1 oz.4. Brush Pressure Arm C4345 1 oz. 5. Brush Holder: Complete Kit - insulated, includes armature terminal stud C3866 4 oz. 5 1/2 . New Armature: All New Repro. (10 1/8" doesn't fit some "SHORT" 1960). Replace your old one & be sure! C11268N 8 lbs. 6. Field Terminal Stud C3864 2 oz. (also see #28, page 83) 7. Large Screws: Side of generator, set of 2. C2861 2 oz./set 8. Field Pole Insulators: 2 needed C3889 1 oz. each 10. Bolts: 7-7/8" C2865 4 oz. 11. Bolt Lock Washers: Set of 2 C2866 1 oz./set 12. Pulley & Fan: 2-7/8" o.d. may vary from original style Discontinued13. Wavy Washer C2774 2 oz. 14. Nut C2775A 2 oz. 15. Field Coils: NEW - Highly suggested. 1961-64 Set C3868 2 lbs./set 16. Inner Spacer C2681 1 oz. 17. Screws - Retainer : Set of 3 C3863 1 oz./set 18. Bearing Retainer C2680 Discontinued See REBUILT GENERATORS: Bottom of page 83 VOLTAGE REGULATORS: See page 84BSWITCH TO ALTERNATOR? See page 84AWe suggest new field coils (#15) & armatures (#5 1/2 ). The originals are old & the insulation is deteriorating. You don't need to switch to an alternator, you need a Clark rebuilt generator.plastic capC8175C2782C2783
Search In Corvair Catalog Content
CLARKS- MORE THAN PARTS.

Copyright © 1978, 2022 Clark's Corvair Parts, Inc., "Clark's Corvair Parts" and the "Corvair Map" are registered service marks of Clark's Corvair Parts, Inc.
400 Mohawk Trail Shelburne Falls, MA 01370 USA All rights reserved.
Main Office Phone: 413.625.9776 Fax: 413.625.8498