i
WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**
72
1960-69 Cars Accelerator Linkage Check the views above carefully. "VIEWS" A & B vary considerably.
Bushing Kits: A KIT with all the rubber and nylon bushings. 2 each of #2, #8, #13, #17, #20. '60–64: C550 2 oz. '65–69: C551 2 oz.
Deluxe Bushing Kit: Includes the BASIC KIT (*) PLUS (•) enough clips (#9, #14, #21), washers (#16), felt washer (#12-65-69), throttle washers (#18-60-65 STD) as
required per the applications as normally needed. (I'd also consider #3, #25 & #32.)
'60–64 STD: C550D 4 oz. '60–64 PG : C550PD 4 oz. '65–69 STD : C551D 4 oz. '65–69 PG: C551PD 4 oz.
½. Nut: Accelerator pedal rod '60–69 C4575 2 oz.
1. Accelerator Pedal: Exact Clark Repro C542R 1 lb.
2. Bushing—Nylon—Pedal Rod: 2 needed (in bushing kit). '60–69 C543 1 oz.
3. Support—Accelerator Pedal Rod: Usually very rusty. '60–64 C7704 4 oz.
Replace before it breaks or rusts tight. '65–69 C7705 4 oz.
5. Bolt—Accelerator Support: Sold set of 2. '60–64 C4576 6 oz./set '65–69 C4577 6 oz./set
7. Accelerator Pedal Rod: Goes through support. '60–64 C1025 6 oz. '65–69 C4578 6 oz.
8. Bushing—Nylon —Accelerator Rod: 2 needed (in bushing kit). '60–69 C544 1 oz.
•9. "C" Clip: Set of 2. C727L ½ oz.
10. Flat Washer '60–64 C545W 1 oz.
•12. Washer—Felt: Allows movement yet keeps it tight. '65–69 ONLY C4579 1 oz.
12½. Thick Steel Washer '65–69 C546W 1 oz.
13. Bushing—Nylon—Pivot Center: 2 needed (in bushing kit). '60–64 C545 1 oz. '65–69 C546 1 oz.
•14. Clip: Original style. '66–69 (also '60–69 clutch linkage). Set of 2. C992 1 oz./set 1965 used "C" clips (see #21).
15. Rear Rod—Back to Transmission Rod: See "NOS" on website & USED page 11
•16. Special Washer: Set of 2. '60–69 C549W 1 oz./set
17. Rubber Bushing: Some '60–64 originally had "teeth"; replacements don't, but work fine. 2 needed (in bushing kit). '60–64: C547 1 oz. '65–69: C548R 1 oz.
•18. Special Throttle Pivot Shaft Washers: Set of 2. '60–65 STD C727W 1 oz. /set
19. Pivot Bolt: Set of 2. '60–64 C4582 2 oz./set '65–69 C4583R 2 oz. (1 special one)
20. Bushing—Nylon: 2 needed (in bushing kit). '60–69 ALL C549 1 oz.
•21. Retainer "C" Clip: Not for 1960 at trans. Set of 5. C727 1 oz. /set
22. Accelerator Rod: From pivot through fire wall to carburetor cross shaft. See "NOS" on website & USED page 11
23. Throttle Bracket Attaching Bolts: Set of 3 bolts & lock washers. '60–65 C11016 6 oz. /set
25. Rear Swivel '60–69 C552 2 oz.
31. Stud —Into Transmission: Originals break easily, don't over tighten. '66–69 ALL
C2438R 4 oz.
32. Rear Accelerator Boot : Where it comes out of tunnel. C101 2 oz.
33. Swivel —Accelerator Rod (#22): To carburetor shaft. Usually worn. '60–69 ALL C7130 2 oz.
PICTURE #
C542R
C548R
C101
