Clark's Corvair Parts, Inc. - Corvair Parts Catalog - Over 12,000 parts

WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**

Turbo Exhaust

PICTURE #

11. Inlet Pipes: From crossover to Turbo base. These are a very good reproduction.

Note that installing a crossover and inlet on a Turbo is a little tricky. Be sure to have

manifolds loose at the head. Everything must be lined up and in place,

then tighten every thing.

1962-64 Style C246R 4 lbs.

1965-66 Style C247R 4 lbs.

12. "Collars" (non-asbestos)

Non-asbestos (heat resistant material) packing ﬁts around pipes where they go

thru shrouds to keep out dust, exhaust and water. Usually need to be replaced each

time removed.

1962–66 Inlet Pipe Collar C250 4 oz.

1962–66 Outlet Pipe Collar C250A 4 oz.

13. Collar Retainers: Inlet and outlet pipes go thru these (slightly different from the original but even the judges will be hard put to tell).

Sold as matched set – upper & lower. Difﬁcult to install.

1962–64 C4374 1 lb.

1965–66 C4375 1 lb.

Retainer Bolts: Hold above retainers into the shrouding – Sold as a full set.

1962-66 Bolt Set C5630 2 oz./set

14. Gasket: Square gasket between inlet and Turbo base.

1962-66 Turbo C245 2 oz.

15. Self Locking Nuts: Hold Turbo to inlet pipe bracket. Sold Set of 4. 1962-66 Turbo C3756 2 oz./set

16. Studs – Bolts: For the Turbo exhaust housing. Holds outlet pipe on.

Note: 1962-63 The exhaust housing outlet on these is a ﬂat, triangular surface and uses bolts (not studs).

1964-66 The exhaust housing outlet is triangular but has a recess for a round "donut gasket" – these use studs.

BOLTS: 1962-63 (Set of 3) C3161 4 oz./set

STUDS: 1964-66 (Set of 3) – Stainless Studs & brass nuts C999 4 oz./set

17.

Outlet Gaskets: See Note with #16 & picture #19. Turbo exhaust housing to outlet pipe.

Flat Triangular Gasket: 1962-63 Style C248 2 oz.

Round "Donut" Gasket: (GRAPHITE) 1964-66 Style C249 4 oz.

18. Outlet Collar: Steel triangular collar holds outlet pipe to Turbo exhaust housing – 1964-66 style.

Original Style Repro. 1964-66 Outlet Collar C1054 1 lb.

19. Outlet Pipes: From TURBO to MUFFLER. See Note #16.

1962-63 C426 6 lbs.

1964 C251 6 lbs.

1965-66 C252 6 lbs.

21. Clamps: Turbo Mufﬂer & Tail Pipe.

Fits 1962-66 Turbo.

2 1/2" Regular Clamp C13A 6 oz.

2 1/2" Heavy Duty Clamp C13AH 8 oz.

MULTI-KITS

see Blue pg. MK-3

Turbo Base Support

See USED page 353

UNIVERSAL JOINTS

See page 167

64-66

62-63

All Aluminized

C1054

iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**41Turbo ExhaustPICTURE #11. Inlet Pipes: From crossover to Turbo base. These are a very good reproduction. Note that installing a crossover and inlet on a Turbo is a little tricky. Be sure to have manifolds loose at the head. Everything must be lined up and in place, then tighten every thing. 1962-64 Style C246R 4 lbs. 1965-66 Style C247R 4 lbs.12. "Collars" (non-asbestos) Non-asbestos (heat resistant material) packing fits around pipes where they go thru shrouds to keep out dust, exhaust and water. Usually need to be replaced each time removed. 1962-66 Inlet Pipe Collar C250 4 oz. 1962-66 Outlet Pipe Collar C250A 4 oz.13. Collar Retainers: Inlet and outlet pipes go thru these (slightly different from the original but even the judges will be hard put to tell). Sold as matched set - upper & lower. Difficult to install. 1962-64 C4374 1 lb. 1965-66 C4375 1 lb. Retainer Bolts: Hold above retainers into the shrouding - Sold as a full set. 1962-66 Bolt Set C5630 2 oz./set14. Gasket: Square gasket between inlet and Turbo base. 1962-66 Turbo C245 2 oz. 15. Self Locking Nuts: Hold Turbo to inlet pipe bracket. Sold Set of 4. 1962-66 Turbo C3756 2 oz./set16. Studs - Bolts: For the Turbo exhaust housing. Holds outlet pipe on. Note: 1962-63 The exhaust housing outlet on these is a flat, triangular surface and uses bolts (not studs). 1964-66 The exhaust housing outlet is triangular but has a recess for a round "donut gasket" - these use studs. BOLTS: 1962-63 (Set of 3) C3161 4 oz./set STUDS: 1964-66 (Set of 3) - Stainless Studs & brass nuts C999 4 oz./set 17. Outlet Gaskets: See Note with #16 & picture #19. Turbo exhaust housing to outlet pipe. Flat Triangular Gasket: 1962-63 Style C248 2 oz. Round "Donut" Gasket: (GRAPHITE) 1964-66 Style C249 4 oz.18. Outlet Collar: Steel triangular collar holds outlet pipe to Turbo exhaust housing - 1964-66 style. Original Style Repro. 1964-66 Outlet Collar C1054 1 lb.19. Outlet Pipes: From TURBO to MUFFLER. See Note #16. 1962-63 C426 6 lbs. 1964 C251 6 lbs. 1965-66 C252 6 lbs.21. Clamps: Turbo Muffler & Tail Pipe. Fits 1962-66 Turbo. 2 1/2" Regular Clamp C13A 6 oz. 2 1/2" Heavy Duty Clamp C13AH 8 oz.MULTI-KITSsee Blue pg. MK-3Turbo Base SupportSee USED page 353UNIVERSAL JOINTSSee page 16764-6662-63All AluminizedC1054