Clark's Corvair Parts, Inc. - Corvair Parts Catalog - Over 12,000 parts

WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**

337

PULLERS – ALL TYPES

There are many rebuilding or removal jobs that just can't be done without a puller.

STEERING WHEEL PULLER

Inexpensive tool that quickly and easily pulls off steering wheels.

Can also be used for pulling crankshaft pulley in a pinch.

I know you'll need this someday. C1119 4 lbs.

Corvair PULLEY PULLER – Solid & Harmonic Style

On 64-69 Corvairs puller only requires you to remove the oil ﬁlter, then you can remove your crank

pulley without removing anything else! On 60-63 motors you must loosen the motor mount bracket

and slide it back on the studs while supporting the engine. Produced by Blue Chip Machine.

C11539 2 lbs.

SEAL PULLER

Wheel bearing seals, axle seals.

C3208 1 lb.

BREAKER BARS

TIE RODS, BALL JOINTS, IDLER ARMS

These "ramped" forks are perfect for "popping" off tie rod ends, ball joints, idler arms, etc.

Remove the nut, insert the fork, and hit once or twice with a hammer.

BALL JOINT, TIE ROD & IDLER ARM BAR (fork) – cars & vans

C950 3 lbs.

VAN STEERING ARM BAR (fork)

Larger size needed for these bigger ends. C5367 4 lbs.

TIE ROD ADJUSTING TOOL

Loosen the clamps on the tie rod sleeve and tool hooks into the slot to turn the sleeve. C5285 1 lb.

• • • SEE "NOS" CATALOG ONLINE • • •

Many parts are only listed in the "NOS" Catalog on our website.

Wheel Spindle Rethreader Die

Rethread damaged threads on front wheel spindle of 1961-65 FC and 1965-69 Cars.

Also for 1965-69 rear wheel spindle. C5289 4 oz.

BEARING PACKER – Allows perfect packing of new or used wheel bearings.

Use with grease gun. C5774 1 lb.

USS & Metric THREAD GAUGES

These silver aluminum gauges make it easy to tell exactly what size bolt or screw you have.

USS #5 3/4" (threads 40tpi–10 tpi), pipe thread (metric & USS combined)

METRIC 2.5mm–22mm (.80mm–2.5mm threads).

C11566 6 oz. (ALL 4 gauges)

BOLT & NUT GAUGE

Push bolt through to get diameter. Fit nuts on studs; ﬁne go on the bottom,

coarse stay on top. Built in length gauge. C12815 6 oz.

C5285

iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**337PULLERS - ALL TYPESThere are many rebuilding or removal jobs that just can't be done without a puller.STEERING WHEEL PULLERInexpensive tool that quickly and easily pulls off steering wheels. Can also be used for pulling crankshaft pulley in a pinch. I know you'll need this someday. C1119 4 lbs.Corvair PULLEY PULLER - Solid & Harmonic StyleOn 64-69 Corvairs puller only requires you to remove the oil filter, then you can remove your crank pulley without removing anything else! On 60-63 motors you must loosen the motor mount bracket and slide it back on the studs while supporting the engine. Produced by Blue Chip Machine. C11539 2 lbs. SEAL PULLER Wheel bearing seals, axle seals. C3208 1 lb.BREAKER BARSTIE RODS, BALL JOINTS, IDLER ARMSThese "ramped" forks are perfect for "popping" off tie rod ends, ball joints, idler arms, etc. Remove the nut, insert the fork, and hit once or twice with a hammer. BALL JOINT, TIE ROD & IDLER ARM BAR (fork) - cars & vans C950 3 lbs. VAN STEERING ARM BAR (fork) Larger size needed for these bigger ends. C5367 4 lbs.TIE ROD ADJUSTING TOOLLoosen the clamps on the tie rod sleeve and tool hooks into the slot to turn the sleeve. C5285 1 lb.o o o SEE "NOS" CATALOG ONLINE o o oMany parts are only listed in the "NOS" Catalog on our website.Wheel Spindle Rethreader DieRethread damaged threads on front wheel spindle of 1961-65 FC and 1965-69 Cars.Also for 1965-69 rear wheel spindle. C5289 4 oz.BEARING PACKER - Allows perfect packing of new or used wheel bearings. Use with grease gun. C5774 1 lb.USS & Metric THREAD GAUGESThese silver aluminum gauges make it easy to tell exactly what size bolt or screw you have. USS #5 3/4" (threads 40tpi-10 tpi), pipe thread (metric & USS combined) METRIC 2.5mm-22mm (.80mm-2.5mm threads). C11566 6 oz. (ALL 4 gauges)BOLT & NUT GAUGEPush bolt through to get diameter. Fit nuts on studs; fine go on the bottom, coarse stay on top. Built in length gauge. C12815 6 oz.C5285