Clark's Corvair Parts, Inc. - Corvair Parts Catalog - Over 12,000 parts

WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**

27A

“LOWER END” PARTS

(refer to picture, page 21)

PICTURE #

22. GASKET – OIL PAN: 1960-69 ALL NOTE: ”Paper” type suggested only for new GM pans or aluminum pans.

Super Cork & Rubber C199 6 oz.

“RUBBERY” composition C3129 6 oz.

“PAPER” – GM style C200 6 oz.

“PAPER” – Aluminum pans C3937 6 oz.

SILICONE C10914 10 oz.

STOCK OIL PAN REINFORCEMENT "RAIL": This steel piece is

about 3/16" thick and completely reinforces the bolting of your stock

steel oil pan and, in most cases, should eliminate leaks. Comes with

correct length bolts, order gasket separately.

C13 374 4 lbs.

23. DRAIN GASKET – 1960-69 ALL: We offer the original style nylon and copper (less apt to crack or allow bolt to loosen).

Nylon C439 1 oz. Copper C6057 1 oz.

24. DRAIN PLUGS: Replace that rounded one. GM but not original style C979 2 oz.

Magnetic C671 2 oz.

REPAIR DRAIN PLUGS: Replace your stripped or leaking drain plug. (Have one just in case!) Self-tapping oversize drain plug and gasket. Just

turn in with a wrench – cuts its own threads. Removable center style is the nicest (oil drains neater than with regular ones).

Oversize C901 2 oz.

Oversize – Removable Center C3338 2 oz.

REPLACEMENT GASKET: For all oversize drain plugs. Copper. C6060 1 oz.

25. OIL PAN – 1960-69 Original Style CX1430 3 lbs.

For Aluminum pans –see page 29-30

26. BOLTS – OIL PAN: Special (may vary slightly from the original) Sold set of 19 C981 8 oz./set

SERRATED WASHER HEAD: Sold as set of 19 For stock pan C7730 8 oz./set

For aluminum pan C7263 8 oz. /set

SEAL SLEEVES: These thin metal sleeves are installed over the old seal area to cover the groove worn by the seal. Each kit

includes the sleeve and tool. Crank seal sleeve can be installed on engine with crank in engine. Crank (fan belt) Pulley Seal Sleeve

C9037 6 oz.

C3338

Phone Busy?

Please wait a few minutes and call again. We have 5 lines and feel that is all we can handle! If you get a busy signal – try again!

UPS Delivery – Special Notes

1. UPS will deliver to your address. Give your full address that someone is usually at.

They will tr y to deliver 3 times, then they will return it to us and you will be liable for shipping.

2. UPS ADDRESS CORRECTIONS: UPS now charges $15.90/package for address corrections for ground shipments.

Please be sure you give us your correct address! If UPS goes to the address you gave us and you, a family member or a

neighbor says "Oh, please deliver it to...instead" we will have to charge you for the address change if UPS charges us.

Performance Cams – formerly “OTTO”

The cam is the heart of your engine. Why settle for the compromised performance of a stock cam when you can have a cam which will perfectly compliment your driv-

ing needs and modiﬁcations (if any) you have made to your engine? With a performance cam, you can beneﬁt from the technology of computer developed cam proﬁles

matched to best compliment the air ﬂow balance in the Corvair cylinder head. The result is a broad power band for better overall performance. With our special series of

proﬁles, (for normally aspirated engines) OT-10 thru OT-40 (and for Turbos) TB-10 thru TB-30 there is a performance camshaft for your performance objective, be it the

ideal street engine or all out competition.

CAM GEARS INSTALLED: We will correctly install a new stock or Failsafe gear with new washer and key. Simply add CG (stock gear) or FG (Failsafe) to the end

of these part num bers. May delay order by 1 day.

PERFORMANCE OUTLINE TB-10 and OT-10

This is the ideal replacement for the Stock Cam where both performance and

economy are impor tant. Results are broader powerband and better driveability. It

works great even with a power glide and good pulling power for heavy loads as with

the truck.

TB-20 and OT-20

A good choice for the enthusiast who wants more performance but does not want

to give up good driveability for the street. Little change in low end performance, big

improvement in midrange power, and higher top end.

TB-30 and OT-30

All around performance with power band starting between 2,000 and 2,500 R.P.M.

Big on mid pow er. The top end will depend on which heads are used and how well

they are prepared. A good choice for prodiﬁed autocross cars. The ideal Cam for all

around dune buggies with "140" Engines.

OT-40

These are all out competition grinds. You may want to make other engine

modiﬁcations to get maximum performance from OT-40 cams.

iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**27A"LOWER END" PARTS(refer to picture, page 21) PICTURE #22. GASKET - OIL PAN: 1960-69 ALL NOTE: "Paper" type suggested only for new GM pans or aluminum pans. Super Cork & Rubber C199 6 oz. "RUBBERY" composition C3129 6 oz. "PAPER" - GM style C200 6 oz. "PAPER" - Aluminum pans C3937 6 oz. SILICONE C10914 10 oz. STOCK OIL PAN REINFORCEMENT "RAIL": This steel piece is about 3/16" thick and completely reinforces the bolting of your stock steel oil pan and, in most cases, should eliminate leaks. Comes with correct length bolts, order gasket separately. C13 374 4 lbs.23. DRAIN GASKET - 1960-69 ALL: We offer the original style nylon and copper (less apt to crack or allow bolt to loosen). Nylon C439 1 oz. Copper C6057 1 oz. 24. DRAIN PLUGS: Replace that rounded one. GM but not original style C979 2 oz. Magnetic C671 2 oz.REPAIR DRAIN PLUGS: Replace your stripped or leaking drain plug. (Have one just in case!) Self-tapping oversize drain plug and gasket. Just turn in with a wrench - cuts its own threads. Removable center style is the nicest (oil drains neater than with regular ones). Oversize C901 2 oz. Oversize - Removable Center C3338 2 oz. REPLACEMENT GASKET: For all oversize drain plugs. Copper. C6060 1 oz. 25. OIL PAN - 1960-69 Original Style CX1430 3 lbs. For Aluminum pans -see page 29-3026. BOLTS - OIL PAN: Special (may vary slightly from the original) Sold set of 19 C981 8 oz./set SERRATED WASHER HEAD: Sold as set of 19 For stock pan C7730 8 oz./set For aluminum pan C7263 8 oz. /set SEAL SLEEVES: These thin metal sleeves are installed over the old seal area to cover the groove worn by the seal. Each kit includes the sleeve and tool. Crank seal sleeve can be installed on engine with crank in engine. Crank (fan belt) Pulley Seal Sleeve C9037 6 oz.C3338Phone Busy? Please wait a few minutes and call again. We have 5 lines and feel that is all we can handle! If you get a busy signal - try again!UPS Delivery - Special Notes1. UPS will deliver to your address. Give your full address that someone is usually at. They will tr y to deliver 3 times, then they will return it to us and you will be liable for shipping.2. UPS ADDRESS CORRECTIONS: UPS now charges $15.90/package for address corrections for ground shipments. Please be sure you give us your correct address! If UPS goes to the address you gave us and you, a family member or a neighbor says "Oh, please deliver it to...instead" we will have to charge you for the address change if UPS charges us.Performance Cams - formerly "OTTO"The cam is the heart of your engine. Why settle for the compromised performance of a stock cam when you can have a cam which will perfectly compliment your driv-ing needs and modifications (if any) you have made to your engine? With a performance cam, you can benefit from the technology of computer developed cam profiles matched to best compliment the air flow balance in the Corvair cylinder head. The result is a broad power band for better overall performance. With our special series of profiles, (for normally aspirated engines) OT-10 thru OT-40 (and for Turbos) TB-10 thru TB-30 there is a performance camshaft for your performance objective, be it the ideal street engine or all out competition.CAM GEARS INSTALLED: We will correctly install a new stock or Failsafe gear with new washer and key. Simply add CG (stock gear) or FG (Failsafe) to the end of these part num bers. May delay order by 1 day.PERFORMANCE OUTLINE TB-10 and OT-10This is the ideal replacement for the Stock Cam where both performance and economy are impor tant. Results are broader powerband and better driveability. It works great even with a power glide and good pulling power for heavy loads as with the truck. TB-20 and OT-20A good choice for the enthusiast who wants more performance but does not want to give up good driveability for the street. Little change in low end performance, big improvement in midrange power, and higher top end.TB-30 and OT-30All around performance with power band starting between 2,000 and 2,500 R.P.M. Big on mid pow er. The top end will depend on which heads are used and how well they are prepared. A good choice for prodified autocross cars. The ideal Cam for all around dune buggies with "140" Engines.OT-40These are all out competition grinds. You may want to make other engine modifications to get maximum performance from OT-40 cams.