Home Order Catalog Online Catalog New Items Contact Us

i
WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**
53
New Turbo Rods & Jets
There are several reasons to replace your old turbo rods and jets:
1. The rods do not stay dead center in the jet; rod rides against the jet & both wear. Sometimes
they wear a lot, leading to poor mileage.
2. Today's gas does not equal gas from the 1960's – requiring a different mix.
3. Chevy supplied a best guess combination.
4. Every turbo motor seems to run a little different.
5. It's not hard. I can easily switch them in under 10 minutes without removing the carb; just the top.
6. We include instructions and additional hints to tell you when you have installed the right jet.
These rods are PRECISION MACHINED in 3 critical areas – "CRUISE," "TRANSITION," and "POWER".
The different diameter of the rod controls the amount of flow through the jet in relation to the throttle.
In order to allow sizes of rods that can be easily machined in the undersizes needed, the jets are slightly
larger and the rod diameters are slightly larger, but have all been calculated to give the same flow as
the original stock sizes (for the "stock" size).
With the following information, you should usually be able to get within one rod size of the correct
combination for your car (expect to experiment). Consider the following example: A person at 2500 ft
may find that the one step richer required by oxygenated gas is cancelled by his elevation and the stock
combination will still work. Our thanks to Chuck Riblett for the info and for producing these parts.
Today's Gas (highest octane available
Oxygenated Adjust 1 Step Richer
Gasohol (10% alcohol) Adjust 2 Steps Richer
E85 (15% alcohol) Adjust 2-3 Steps Richer
Elevation
Sea Level – 1500 f t. No Change
1500 – 3000 ft. 1 Step Leaner
3000 – 4500 ft. 2 Steps Leaner
4500 – 6000 ft. 3 Steps Leaner
PING?!? Check all tune-up aspects. Clean all flashing out of
heads when rebuilding. Pressure retard working? (Use reinforced
hose and clamps.) If you experience ping, YOU MUST ELIMINATE
ANY MORE THAN 1-2 PINGS!! Ping can ruin a turbo engine quickly.
GO RICHER.
CLARK'S REBUILDING YOUR TURBO CARB? Tell us which rod & jet you'd like us to install.
Extra charge applies. NOTE: These rods & jets CANNOT be used with originaI rods & jets.
The new "stock" jet is used with all the related rods for that year. Sorry, ABSOLUTELY NO RE TURNS ON RODS OR JETS! A few "late" 63's & "early" 65's were slightly
different, but these will work fine. See the list that follows for carb identification. IN STOCK!
Year "Stock" Jet "Stock" Rod Rod 1-Richer Rod 2-Richer Rod 3-Richer Rod 1-Leaner Rod 2-Leaner Rod 3-Leaner
1962 C5782J C5782R C5782R1 C5782R2 C5782R3 C5782L1 C5782L2 C5782L3
1963–64 C5783J C5783R C5783R1 C5783R2 C5783R3 C5783L1 C5783L2 C5783L3
1965–66 C5785J C5785R C5785R1 C5785R2 C5785R3 C5785L1 C5785L2 C5785L3
The following lists the turbo carb tag # & body # that relate to above char t:
1962 Tag #: 3311S, 3311SA, 3569S Body #: 0-1392, 0-1507
1963–64 Tag #: 3586S, 3586SA, 3692S, 3692SA Body #: 0-1580
1965–66 Tag #: 3902S, 4020S, 4141S, 4141SA Body #: 0-1750, 0-1769
Clark’s Only Charge You the ACTUAL SHIPPING!
All our shipping and invoicing is computerized. Our billing with UPS is "Computer Manifested".
You are ONLY CHARGED FOR THE ACTUAL UPS OR POST OFFICE RATES and you never have to worry
about being OVERCHARGED 20–50% by someone "adding" a little to your shipping bill (and their prot!).
Also, WE HAVE NO HANDLING CHARGE!
Friendly, Understandable Tech Help is FREE from Clark's Corvair Parts, Inc.
It seems these days every time you call for technical support that your call is answered by some far away voice or a computer mailbox system that makes it
difficult, if not impossible, to communicate. Not so at Clark's Corvair Parts, Inc. Our tech people are located right here at Clark's, where they have been for over 35
years. Our techs have over 75 years of combined technical experience helping you solve Corvair problems. At Clark's, your tech questions are answered quickly,
concisely and accurately by someone who understands you and your problem and makes every effort to help you find a solution.
Best of all, this amazing resource is available absolutely FREEl
Why are some of the Repro Trim Parts
only available in Pairs?
Many customers have asked this question. To save cost,
they put both pieces in the same tooling. This does two things:
1. It cuts the cost of tooling
2. It also allows the use of just one piece of metal to stamp
both pieces in turn saving on labor & reducing waste.
Another benefit, they only have one tooling to stock
& 1 set up when we reorder.
uMulti-Kits Have Built-In Additional Discounts
Be sure to check out the blue Multi-Kit section of the Catalog before ordering.
iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**53New Turbo Rods & JetsThere are several reasons to replace your old turbo rods and jets:1. The rods do not stay dead center in the jet; rod rides against the jet & both wear. Sometimes they wear a lot, leading to poor mileage.2. Today's gas does not equal gas from the 1960's - requiring a different mix.3. Chevy supplied a best guess combination.4. Every turbo motor seems to run a little different.5. It's not hard. I can easily switch them in under 10 minutes without removing the carb; just the top.6. We include instructions and additional hints to tell you when you have installed the right jet.These rods are PRECISION MACHINED in 3 critical areas - "CRUISE," "TRANSITION," and "POWER". The different diameter of the rod controls the amount of flow through the jet in relation to the throttle. In order to allow sizes of rods that can be easily machined in the undersizes needed, the jets are slightly larger and the rod diameters are slightly larger, but have all been calculated to give the same flow as the original stock sizes (for the "stock" size).With the following information, you should usually be able to get within one rod size of the correct combination for your car (expect to experiment). Consider the following example: A person at 2500 ft may find that the one step richer required by oxygenated gas is cancelled by his elevation and the stock combination will still work. Our thanks to Chuck Riblett for the info and for producing these parts. Today's Gas (highest octane availableOxygenated Adjust 1 Step RicherGasohol (10% alcohol) Adjust 2 Steps RicherE85 (15% alcohol) Adjust 2-3 Steps RicherElevationSea Level - 1500 f t. No Change1500 - 3000 ft. 1 Step Leaner3000 - 4500 ft. 2 Steps Leaner4500 - 6000 ft. 3 Steps LeanerPING?!? Check all tune-up aspects. Clean all flashing out of heads when rebuilding. Pressure retard working? (Use reinforced hose and clamps.) If you experience ping, YOU MUST ELIMINATE ANY MORE THAN 1-2 PINGS!! Ping can ruin a turbo engine quickly. GO RICHER.CLARK'S REBUILDING YOUR TURBO CARB? Tell us which rod & jet you'd like us to install. Extra charge applies. NOTE: These rods & jets CANNOT be used with originaI rods & jets. The new "stock" jet is used with all the related rods for that year. Sorry, ABSOLUTELY NO RE TURNS ON RODS OR JETS! A few "late" 63's & "early" 65's were slightly different, but these will work fine. See the list that follows for carb identification. IN STOCK! Year "Stock" Jet "Stock" Rod Rod 1-Richer Rod 2-Richer Rod 3-Richer Rod 1-Leaner Rod 2-Leaner Rod 3-Leaner1962 C5782J C5782R C5782R1 C5782R2 C5782R3 C5782L1 C5782L2 C5782L31963-64 C5783J C5783R C5783R1 C5783R2 C5783R3 C5783L1 C5783L2 C5783L31965-66 C5785J C5785R C5785R1 C5785R2 C5785R3 C5785L1 C5785L2 C5785L3The following lists the turbo carb tag # & body # that relate to above char t:1962 Tag #: 3311S, 3311SA, 3569S Body #: 0-1392, 0-15071963-64 Tag #: 3586S, 3586SA, 3692S, 3692SA Body #: 0-15801965-66 Tag #: 3902S, 4020S, 4141S, 4141SA Body #: 0-1750, 0-1769Clark's Only Charge You the ACTUAL SHIPPING!All our shipping and invoicing is computerized. Our billing with UPS is "Computer Manifested". You are ONLY CHARGED FOR THE ACTUAL UPS OR POST OFFICE RATES and you never have to worry about being OVERCHARGED 20-50% by someone "adding" a little to your shipping bill (and their pro?t!). Also, WE HAVE NO HANDLING CHARGE!Friendly, Understandable Tech Help is FREE from Clark's Corvair Parts, Inc.It seems these days every time you call for technical support that your call is answered by some far away voice or a computer mailbox system that makes it difficult, if not impossible, to communicate. Not so at Clark's Corvair Parts, Inc. Our tech people are located right here at Clark's, where they have been for over 35 years. Our techs have over 75 years of combined technical experience helping you solve Corvair problems. At Clark's, your tech questions are answered quickly, concisely and accurately by someone who understands you and your problem and makes every effort to help you find a solution. Best of all, this amazing resource is available absolutely FREElWhy are some of the Repro Trim Parts only available in Pairs?Many customers have asked this question. To save cost, they put both pieces in the same tooling. This does two things: 1. It cuts the cost of tooling2. It also allows the use of just one piece of metal to stamp both pieces in turn saving on labor & reducing waste.Another benefit, they only have one tooling to stock & 1 set up when we reorder.uMulti-Kits Have Built-In Additional Discounts Be sure to check out the blue Multi-Kit section of the Catalog before ordering.
Search In Corvair Catalog Content
CLARKS- MORE THAN PARTS.

Copyright © 1978, 2022 Clark's Corvair Parts, Inc., "Clark's Corvair Parts" and the "Corvair Map" are registered service marks of Clark's Corvair Parts, Inc.
400 Mohawk Trail Shelburne Falls, MA 01370 USA All rights reserved.
Main Office Phone: 413.625.9776 Fax: 413.625.8498