Clark's Corvair Parts, Inc. - Corvair Parts Catalog - Over 12,000 parts

WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**

131

TRANSMISSION

1961-65 4-SPEED – ALL PARTS FIT 1961-65 UNLESS OTHERWISE NOTED. REFER TO PICTURE DIAGRAM PAGE 130.

PICTURE #

42. Rear Bearing (Differential) End: 1960-61 Cars & Vans (1st design – no shield – PREMIUM) C1672 12 oz.

1962-65 ALL 4-Spds. (order C1672 or $$ SAVER) $$ SAVER C8459 12 oz. (Shield style may vary but they work fine.)

43. Bearing Locating Ring: Comes on bearing – 1962-65 C2616 2 oz.

45. 1st Gear: 1961-63 CX1683 4 lbs.

49. Gear Shift Fork: See "NOS" on website

50. Interlock C9860 1 oz. (Check Availability)

51. Interlock Pin C3595 1 oz.

53. Main Drive Gear – Clutch Gear: See "NOS" on website

54. Pins – Fork Heads C3384 1 oz.

57. Rollers – Main Shaft: Clutch Gear C1864 ½ oz.

FU LL SET C1864A 6 oz./set

58. Ring – Hub Retaining C2615 2 oz.

Special Spacer: 1961-65 4 Spd. Often missing! Exact repro. C9387 2 oz.

59. Freeze Plug (61-64 4 spd.): 2 needed. Old ones can leak. Need to remove for full rebuild. C8071 1 oz.

TRANSMISSION

'66-69

3 & 4

Speed

ALL PARTS ARE

INTERCHANGEABLE

(exc. as noted)

Transmission Shims

see page 167A

MULTI-KITS

see Blue pg. MK-10

PICTURE # Also see "NOS" on website

2. Counter Shaft: 4 speed C1856 1 lb. (seldom have)

3. Washer – Large Counter Shaft Thrust: 2 needed C1859 Discontinued

4. Washer – Small Counter Shaft Thrust: 2 needed C1860 Discontinued

5. Rollers: Needle Bearings Counter Shaft Gear C1862 ½ oz.

FULL SET C1862A 6 oz./set

7. Reverse Idler Shaft: 3 speed Discontinued

8. Counter Shaft Gear Assembly: 3 Speed – 1966-69 C2635 10 lbs.

4 Speed – 1966-68 CX1582 10 lbs.

4 Speed – 1969 C3854 10 lbs.

9. Reverse Idler Gear: 3 Speed – 1966-69 C4406 1 lb . 4 Speed - 1966-69 C1850 Discontinued

15. Plug C4383 4 oz.

17. Selec tor Shaft Discontinued

18. Seal – Selector Shaft : Shifter Shaft – Comes out front of transmission C497 2 oz. (Clark improved seal)

19. Front Main Bearing – Clutch Bearing: Either of the following bearings were used from 1966-69 and are interchangeable:

We have given the number found on the shield if you want to match the same bearing you have.

(#47507) PREMIUM : C1672 12 oz. (#47207) PREMIUM – (sub C1672) $$ SAVER (66-69 ALL): C8459 12 oz.

20. Ring – Clutch Gear Bearing Locating Ring : Comes with bearing C2616 2 oz.

21. Snap Ring: Bearing to clutch gear C2625 2 oz.

22. Cover Gasket: Comes in Gasket Set C4401 4 oz.

23. End Bearing Cover C3406 10 oz.

23½. Set Of 4 Bolts & Special Lock Washers C4402 2 oz./set

24. 2nd Gear – 3 Speed Trans. C3408 3 lbs.

3rd Gear – 4 Speed Trans. C2631 3 lbs.

PREMIUM BEARINGS: "Name Brand" Bearings (BCA, KOYO, SKF,

TIMKEN, etc.). Usually made in USA, Canada, Mexico or Europe.

$$ SAVER BEARINGS: "QUALITY" BEARINGS usually made in China.

Acceptable bearings but NOT considered EQUAL to composition of

"PREMIUM" BEARINGS.

C6850

Gasket Set: As shown – All gaskets and seals – Complete Set. C185 6 oz.

Transmission to Differential Gasket: Separately C2211 4 oz.

Back Up Switch: See page 84B

Small Parts Kits: Nearly all thrust washers, snap rings, clips, that you would need (over 20 parts). Also available with or without all roller bearings. (#5 & #35)

WITH ROLLERS WITHOUT ROLLERS

1966-69 3 & 4 Speed

C6849 8 oz. C6850 6 oz.

C9387

See page 128

iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**131TRANSMISSION1961-65 4-SPEED - ALL PARTS FIT 1961-65 UNLESS OTHERWISE NOTED. REFER TO PICTURE DIAGRAM PAGE 130.PICTURE # 42. Rear Bearing (Differential) End: 1960-61 Cars & Vans (1st design - no shield - PREMIUM) C1672 12 oz. 1962-65 ALL 4-Spds. (order C1672 or $$ SAVER) $$ SAVER C8459 12 oz. (Shield style may vary but they work fine.)43. Bearing Locating Ring: Comes on bearing - 1962-65 C2616 2 oz. 45. 1st Gear: 1961-63 CX1683 4 lbs.49. Gear Shift Fork: See "NOS" on website50. Interlock C9860 1 oz. (Check Availability)51. Interlock Pin C3595 1 oz.53. Main Drive Gear - Clutch Gear: See "NOS" on website54. Pins - Fork Heads C3384 1 oz.57. Rollers - Main Shaft: Clutch Gear C1864 1/2 oz. FU LL SET C1864A 6 oz./set58. Ring - Hub Retaining C2615 2 oz. Special Spacer: 1961-65 4 Spd. Often missing! Exact repro. C9387 2 oz.59. Freeze Plug (61-64 4 spd.): 2 needed. Old ones can leak. Need to remove for full rebuild. C8071 1 oz.TRANSMISSION'66-693 & 4 SpeedALL PARTS ARE INTERCHANGEABLE (exc. as noted)Transmission Shimssee page 167AMULTI-KITSsee Blue pg. MK-10PICTURE # Also see "NOS" on website2. Counter Shaft: 4 speed C1856 1 lb. (seldom have)3. Washer - Large Counter Shaft Thrust: 2 needed C1859 Discontinued4. Washer - Small Counter Shaft Thrust: 2 needed C1860 Discontinued5. Rollers: Needle Bearings Counter Shaft Gear C1862 1/2 oz. FULL SET C1862A 6 oz./set7. Reverse Idler Shaft: 3 speed Discontinued8. Counter Shaft Gear Assembly: 3 Speed - 1966-69 C2635 10 lbs. 4 Speed - 1966-68 CX1582 10 lbs. 4 Speed - 1969 C3854 10 lbs.9. Reverse Idler Gear: 3 Speed - 1966-69 C4406 1 lb . 4 Speed - 1966-69 C1850 Discontinued15. Plug C4383 4 oz.17. Selec tor Shaft Discontinued18. Seal - Selector Shaft : Shifter Shaft - Comes out front of transmission C497 2 oz. (Clark improved seal)19. Front Main Bearing - Clutch Bearing: Either of the following bearings were used from 1966-69 and are interchangeable: We have given the number found on the shield if you want to match the same bearing you have. (#47507) PREMIUM : C1672 12 oz. (#47207) PREMIUM - (sub C1672) $$ SAVER (66-69 ALL): C8459 12 oz.20. Ring - Clutch Gear Bearing Locating Ring : Comes with bearing C2616 2 oz.21. Snap Ring: Bearing to clutch gear C2625 2 oz. 22. Cover Gasket: Comes in Gasket Set C4401 4 oz.23. End Bearing Cover C3406 10 oz.23 1/2 . Set Of 4 Bolts & Special Lock Washers C4402 2 oz./set24. 2nd Gear - 3 Speed Trans. C3408 3 lbs. 3rd Gear - 4 Speed Trans. C2631 3 lbs.PREMIUM BEARINGS: "Name Brand" Bearings (BCA, KOYO, SKF, TIMKEN, etc.). Usually made in USA, Canada, Mexico or Europe. $$ SAVER BEARINGS: "QUALITY" BEARINGS usually made in China. Acceptable bearings but NOT considered EQUAL to composition of "PREMIUM" BEARINGS.C6850Gasket Set: As shown - All gaskets and seals - Complete Set. C185 6 oz.Transmission to Differential Gasket: Separately C2211 4 oz.Back Up Switch: See page 84BSmall Parts Kits: Nearly all thrust washers, snap rings, clips, that you would need (over 20 parts). Also available with or without all roller bearings. (#5 & #35)WITH ROLLERS WITHOUT ROLLERS1966-69 3 & 4 SpeedC6849 8 oz. C6850 6 oz.36C9387See page 128