Clark's Corvair Parts, Inc. - Corvair Parts Catalog - Over 12,000 parts

WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**

321

MORE INDIVIDUAL A/C PARTS

1961-64 ALL CARS

Engine Lid Seal – C805RRAC 3 lbs.

Required for 61-64 engine lid mount condenser kits. Not needed for trunk mounted condenser kits. Comes with instructions. Recommended glue is

C4870R.

Small Chrome Air Filters: Required for use with 64 Engine Mounted Condenser Kit (C11781 on page 318.)

We've done the extra work so you can easily install these chrome air ﬁlters. ORDER 1 KIT with PCV brass ﬁtting so you can attach a hose from the PCV

tube. ALSO ORDER 1 or more WITHOUT. We supply all the parts and complete instructions for an easy, professional looking installation. 140 order (1)

C11611 & (3) C11612. KITS give you ALL PARTS FOR 1 CARB.

CHROME AIR FILTER KIT – WITH PCV ﬁtting C11611 1 lb.

CHROME AIR FILTER KIT – NO PCV ﬁtting C11612 1 lb.

REPLACEMENT PAPER ELEMENT C11613 1 lb.

Note: If you don't want to use this style air ﬁlter, you could try to adapt 61-63 style air cleaners.

This requires many parts and modiﬁcations to the top of carbs.

61-63 Repro A/C Motor Mount – C8056AR 4 lbs.

64 Style, 61-63 Car & 61-65 FC A/C Engine Mount Bracket, Repro – C11847 3 lbs.

Have a non-air conditioned 61-63? If so, you will need this piece. Most 61-63 cars had the "ﬂat" version of this lower engine bracket, but A/C cars need

this "clearance" version to make room for the A/C pulley. It came stock on all 64's. We have made some modiﬁcations and now have this hard to ﬁnd

part available. You also need C11943 rear cover (C11943 below). Satin black ﬁnish.

"A & B" – 61-64 Rear Engine Seal Retainers – C6804 & C6805 4 oz. ea.

These metal retainers attach to the rear shrouds to hold the rubber strip to the rear of the

engine. 3 pieces needed. (2 "A" & 1 "B")

"A" (ﬁts left or right side) "B" Center section – Slips into

2 needed C6804 "A" at either end C6805

"C" – Seal, Engine to Body: Fabric reinforced rubber. C389A 8 oz.

"D" – 61-64 and 61-65 FC Skid Plate Cover, Repro – C11943 1 lb.

This is the small rectangular steel cover behind the motor mount that helps seal

the engine compartment. We also recommend the rear engine seal retainers listed

above (C6804 & C6805).

61-65 FC Repro A/C Pulley w/ Bolt – C11945 2 lbs.

Original 6" size. Includes all needed bolts. Does Not look stock. This style is designed after

the 1964-67 pulley that bolted to the harmonic balancer. Building your own A/C system on an FC? We have the pulley and

bracket that you will need to make the conversion. We have designed this pulley especially for the FC knowing the tight area

you have to work with. Pulley bolts onto crank pulley same as stock A/C pulleys, but is tight to the crank pulley to allow

enough room to run this along with the stock 64 bracket or our repro bracket. No modiﬁcation needed for the upper motor

mount support. Once installed changing the regular fan belt will be more work as there is not enough clearance left to get the

inner belt on and off without removing the rear air grill and motor mount nut to lower the motor down and then remove the

rear motor mount bracket. Satin black ﬁnish. All 61-63 & FC must also order 64 style engine mount bracket (C11847). Also

see skid plate cover (C11943) above.

1965-69 CARS

In-Dash Vent Kit, 65-69 Cars – C11856 2 lbs.

If you want to add A/C to a car that never had it, and want that in-dash look, then this is your kit. Kit includes one rectangular plastic chrome vent that

mounts just above the radio and two round plastic chrome vents for either side of the dash. All vents use• 2" vent hose (C11838). While not stock, these

do look more correct than the under-dash version, but are more difﬁcult to install. Cutting of dash is required for installation.

Glove box, 65-69 Plastic Replacement – C11792 2 lbs.

This new glove box is a 2-piece, vacuum-formed plastic alternative to the factory cardboard version. Not as

deep as the original so it gives you a little more room for the cramped evaporator and passenger vent hose

area. A must have for evaporator installation.

Drier, 65-67 Replacement – C11806 2 lbs.

An aftermarket replacement for your stock drier. This affordable drier

is good for either R-12 or R-134 refrigerant, and will ﬁt your 65-67 stock drier bracket and look great. Includes a sight glass for R-12 use and modern

o-ring style ports. No ﬁttings included – See page 318 for kit (C11857). *Note: This drier is close to stock dimensions but the outside diameter is a little

smaller. It can easily be shimmed to ﬁt your stock bracket. Also note that if your A/C system has been opened for more than a few minutes, you have to

replace your existing drier with a new one before recharging! Also read "Why Replace the Drier?" on page 318.

Seal, 66-67 Stock & Repro Condenser – C11811 1 lb.

These two foam seal strips are required on 66-67 condensers. Dark grey, stock with a 1" x 1" cross section.

C11847

C11943

iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**321MORE INDIVIDUAL A/C PARTS1961-64 ALL CARSEngine Lid Seal - C805RRAC 3 lbs.Required for 61-64 engine lid mount condenser kits. Not needed for trunk mounted condenser kits. Comes with instructions. Recommended glue is C4870R.Small Chrome Air Filters: Required for use with 64 Engine Mounted Condenser Kit (C11781 on page 318.)We've done the extra work so you can easily install these chrome air filters. ORDER 1 KIT with PCV brass fitting so you can attach a hose from the PCV tube. ALSO ORDER 1 or more WITHOUT. We supply all the parts and complete instructions for an easy, professional looking installation. 140 order (1) C11611 & (3) C11612. KITS give you ALL PARTS FOR 1 CARB. CHROME AIR FILTER KIT - WITH PCV fitting C11611 1 lb. CHROME AIR FILTER KIT - NO PCV fitting C11612 1 lb. REPLACEMENT PAPER ELEMENT C11613 1 lb.Note: If you don't want to use this style air filter, you could try to adapt 61-63 style air cleaners. This requires many parts and modifications to the top of carbs.61-63 Repro A/C Motor Mount - C8056AR 4 lbs.64 Style, 61-63 Car & 61-65 FC A/C Engine Mount Bracket, Repro - C11847 3 lbs.Have a non-air conditioned 61-63? If so, you will need this piece. Most 61-63 cars had the "flat" version of this lower engine bracket, but A/C cars need this "clearance" version to make room for the A/C pulley. It came stock on all 64's. We have made some modifications and now have this hard to find part available. You also need C11943 rear cover (C11943 below). Satin black finish."A & B" - 61-64 Rear Engine Seal Retainers - C6804 & C6805 4 oz. ea.These metal retainers attach to the rear shrouds to hold the rubber strip to the rear of the engine. 3 pieces needed. (2 "A" & 1 "B") "A" (fits left or right side) "B" Center section - Slips into 2 needed C6804 "A" at either end C6805"C" - Seal, Engine to Body: Fabric reinforced rubber. C389A 8 oz."D" - 61-64 and 61-65 FC Skid Plate Cover, Repro - C11943 1 lb.This is the small rectangular steel cover behind the motor mount that helps seal the engine compartment. We also recommend the rear engine seal retainers listed above (C6804 & C6805).61-65 FC Repro A/C Pulley w/ Bolt - C11945 2 lbs.Original 6" size. Includes all needed bolts. Does Not look stock. This style is designed after the 1964-67 pulley that bolted to the harmonic balancer. Building your own A/C system on an FC? We have the pulley and bracket that you will need to make the conversion. We have designed this pulley especially for the FC knowing the tight area you have to work with. Pulley bolts onto crank pulley same as stock A/C pulleys, but is tight to the crank pulley to allow enough room to run this along with the stock 64 bracket or our repro bracket. No modification needed for the upper motor mount support. Once installed changing the regular fan belt will be more work as there is not enough clearance left to get the inner belt on and off without removing the rear air grill and motor mount nut to lower the motor down and then remove the rear motor mount bracket. Satin black finish. All 61-63 & FC must also order 64 style engine mount bracket (C11847). Also see skid plate cover (C11943) above.1965-69 CARSIn-Dash Vent Kit, 65-69 Cars - C11856 2 lbs.If you want to add A/C to a car that never had it, and want that in-dash look, then this is your kit. Kit includes one rectangular plastic chrome vent that mounts just above the radio and two round plastic chrome vents for either side of the dash. All vents useo 2" vent hose (C11838). While not stock, these do look more correct than the under-dash version, but are more difficult to install. Cutting of dash is required for installation.Glove box, 65-69 Plastic Replacement - C11792 2 lbs.This new glove box is a 2-piece, vacuum-formed plastic alternative to the factory cardboard version. Not as deep as the original so it gives you a little more room for the cramped evaporator and passenger vent hose area. A must have for evaporator installation.Drier, 65-67 Replacement - C11806 2 lbs.An aftermarket replacement for your stock drier. This affordable drier is good for either R-12 or R-134 refrigerant, and will fit your 65-67 stock drier bracket and look great. Includes a sight glass for R-12 use and modern o-ring style ports. No fittings included - See page 318 for kit (C11857). *Note: This drier is close to stock dimensions but the outside diameter is a little smaller. It can easily be shimmed to fit your stock bracket. Also note that if your A/C system has been opened for more than a few minutes, you have to replace your existing drier with a new one before recharging! Also read "Why Replace the Drier?" on page 318.Seal, 66-67 Stock & Repro Condenser - C11811 1 lb.These two foam seal strips are required on 66-67 condensers. Dark grey, stock with a 1" x 1" cross section.C11847C11943