Clark's Corvair Parts, Inc. - Corvair Parts Catalog - Over 12,000 parts

WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**

SEAT SPRING CLIPS: We offer the original style that allow free movement. Sold set of 5. C13175 4 oz.

TIGHTER CLIPS: We suggest these spring clips if you have an area where you need to get the springs tighter but do not need

quite as much movement. Note: Do not remove the "paper liner" as it helps prevent noise. Sold set of 5. C13176 2 oz.

Paper Covered Wire: All Corvair upholstery has wire in the listing – it is often paper covered. The paper covering

kept the wire from cutting through the listing and as the hog rings gripped the paper covering, kept the wire from moving. Zigzag wire

and even bare wire was used (bare wire rusts & is more apt to cut through the listing). We are offering thin & thick wire. The thin wire

will work for all car & FC upholstery. The thicker wire was used in several places that Chevy thought there would be more stress.

25 Feet is plenty for the FC front seat (they often used thick). 50 Feet is plenty for any car or FC with rear seats. Why replace?

Usually the old paper has deteriorated. Bare wire must be sanded or the rust can quickly deteriorate the listing.

Thin Paper Covered Wire (most often used thickness)

25 Feet C9064A 1 lb.

Sample: C9064X

50 Feet C9064W 2 lbs.

Thick Paper Covered Wire (often for FC & limited areas in car & bucket seat)

25 Feet C10019W 1 lb. 4 oz.

Sample: C10019A

50 Feet C10020W 2 lbs. 8 oz.

FOAM: FC's & 4-Dr Monza Rear Seats and some 500/700s: This is a premium quality automotive grade foam, it is not the low density

stuff!!!!! We offer 3 different densities for the seat bottoms & 1 for the seat backs.

FC'S: All FC's used foam on all of the seats & it almost always needs replacing. On the earlier FC's it was just a piece of

foam; on the later ones it was formed slightly to wrap around the seats. Ours are just sheets & will work great. They also

used a layer of cotton on top.

FC Seat Tops (Front & Rear): These originally used an "ultra plush" 3/4" foam which we have increased to 1"

(don't forget the cotton). Some "regular" models did not use foam in the top, just cotton. You can add the foam &

1 layer of cotton for greater comfort.

Custom/Delux Seat Bottoms: FABRIC or VINYL, front or rear, used a 1 1/2" foam that was approximately half way

between our "plush" and "firm". We also offer an "extra firm" if you want to increase the stiffness of your seat. It will be a

little harder to install. Most modern car seats are closer to the "extra firm". Don't forget the cotton.

Regular FC Interiors Bottoms: Non-custom, non-delux & non-Greenbriers. These used the "plush" foam in 1 1/4",

we've increased that to 1 1/2". You can also move up to the "firm" foam if you want. Don't forget the cotton.

Bench Seats & 4 Dr Rear Seats: Please check your seats to see how they were constructed.

Comes in sheets 1= 24" x 66" they're bulky & do not compress very much. Weights vary depending on quantities ordered & packing required.

Ultra Plush: 1" (seat backs only) C13177 4 lbs. Sample: C13177A

Plush: 1 1/2" (seat bottoms) C13178 6 lbs. Sample: C13178A

Firm: 1 1/2" (seat bottoms) C13179 6 lbs. Sample: C13179A

Extra Firm: 1 1/2" (seat bottoms) C13180 6 lbs. Sample: C13180A

Non-Cotton: This is a synthetic material that is not quite as dense as cotton, but "stays together" better than cotton. You may want to use several layers

instead of the cotton, but note that it is NOT as firm as cotton, but does have slightly better "memor y". The ½" is slightly denser & very useful for bucket seat

cotton replacement on top of the seat buns as it stays together & stays put better than cotton. Note: Each non-bucket seat needs approx 55-66" & may need

double layers. When you measure, allow 2-3" of overhang on each end.

Non-Cotton 1/2" (slightly denser) 1 = 27" x 1 yd C13220 1 lb./yd Sample: C13220A

Non-Cotton 3/4" 1 = 27" x 1 yd C13221 10 oz./yd Sample: C13221A

Non-Cotton 2" 1 = 30" x 1 yd C13223 1 lb./yd Sample: C13223A

7⁄16" (semi-firm foam) 1 = 24" x 54" 2 = 24" x 108" C13085 3 lbs. /yd Sample: C13086

Padding: Many seats used an "under padding", that was under the cotton layer and usually on top of the burlap. It might be dense cotton with burlap (or

another mesh glued on) or it may be a jute-like material or even a dense felt material. You may choose to glue together several layers of cotton & a layer of burlap,

or use 1 or 2 layers of our dense padding or even 1 or 2 layers of carpet padding or the ¼" jute. We suggest you get our full sample kit below so you can

decide. See 3M glue bottom of page 265A.

PADDING: These are some of our products that you may want to use to replace the "under padding". Also see Felt.

Note: Each non-bucket seat needs approx 55-66" & may need double layers; when you measure allow 2-3" of overhang on each end.

Dense Pad: Non-Cotton 3/4" 1 = 27" x 1 yd C13224 1 lb./yd Sample: C13224A

Carpet Padding: 1/2" – sold by the yard 1 = 36" x 1 yd 2 = 36" x 2 yds., etc. C3801 3 lbs./yd. (most seats need Sample: C3801A

55-66" per layer)

Felt: Felt was used in various places on some seats. Bucket seats and other seats had some 1⁄8" felt glued to the frame to cushion the upholstery that might rub

against it. Bucket seats & other seats had ¼" felt hog ringed & hanging in the seat or between springs. It is often musty or torn. Several layers of ¼" can be glued

together to produce a replacement for jute or felt "under padding". Note: Each non-bucket seat needs approx 55-66" & may need double layers.

1 ⁄ 8" Felt (approx thickness) 1 = 36" x 1 yd C13225 10 oz. /yd Sample: C13225A

1/4" Felt 1 = 40" x 1 yd C13226 1 lb./yd Sample: C13226A

SET: Cotton, Burlap, Non-Cotton – Dense Padding, Felt, etc.

You will receive samples of ALL of our materials (including paper covered wire) along with additional hints & info on how to fully restore your seats.

Order C1445C – FREE with a par ts order. If ordering just the samples we do have to charge for shipping.

SET: Foam.

Mostly used for FC's & 4 doors. You will get a small sample of each of the 4 foams listed below. It is easier to tell the difference when you have a square foot of

material but we cannot send that much. We will include hints to help you tell the differences & what to expect if you use that foam.

Order C2825F – FREE with a parts order. If ordering just the foam samples we do have to charge for shipping.

2 pieces approx 44 lbs., 3 pieces approx. 59 lbs. due to

size. We pack as economically as possible to save you

money on shipping.

Note: For firm or extra

firm, we suggest a layer

of regular burlap on top

& pulled snuggly over the

foam – it helps it to wrap

around front & sides.

265B

C13175

iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**SEAT SPRING CLIPS: We offer the original style that allow free movement. Sold set of 5. C13175 4 oz.TIGHTER CLIPS: We suggest these spring clips if you have an area where you need to get the springs tighter but do not need quite as much movement. Note: Do not remove the "paper liner" as it helps prevent noise. Sold set of 5. C13176 2 oz.Paper Covered Wire: All Corvair upholstery has wire in the listing - it is often paper covered. The paper covering kept the wire from cutting through the listing and as the hog rings gripped the paper covering, kept the wire from moving. Zigzag wire and even bare wire was used (bare wire rusts & is more apt to cut through the listing). We are offering thin & thick wire. The thin wire will work for all car & FC upholstery. The thicker wire was used in several places that Chevy thought there would be more stress. 25 Feet is plenty for the FC front seat (they often used thick). 50 Feet is plenty for any car or FC with rear seats. Why replace? Usually the old paper has deteriorated. Bare wire must be sanded or the rust can quickly deteriorate the listing. Thin Paper Covered Wire (most often used thickness) 25 Feet C9064A 1 lb. Sample: C9064X 50 Feet C9064W 2 lbs. Thick Paper Covered Wire (often for FC & limited areas in car & bucket seat) 25 Feet C10019W 1 lb. 4 oz. Sample: C10019A 50 Feet C10020W 2 lbs. 8 oz. FOAM: FC's & 4-Dr Monza Rear Seats and some 500/700s: This is a premium quality automotive grade foam, it is not the low density stuff!!!!! We offer 3 different densities for the seat bottoms & 1 for the seat backs. FC'S: All FC's used foam on all of the seats & it almost always needs replacing. On the earlier FC's it was just a piece of foam; on the later ones it was formed slightly to wrap around the seats. Ours are just sheets & will work great. They also used a layer of cotton on top.FC Seat Tops (Front & Rear): These originally used an "ultra plush" 3/4" foam which we have increased to 1" (don't forget the cotton). Some "regular" models did not use foam in the top, just cotton. You can add the foam & 1 layer of cotton for greater comfort.Custom/Delux Seat Bottoms: FABRIC or VINYL, front or rear, used a 1 1/2" foam that was approximately half way between our "plush" and "firm". We also offer an "extra firm" if you want to increase the stiffness of your seat. It will be a little harder to install. Most modern car seats are closer to the "extra firm". Don't forget the cotton.Regular FC Interiors Bottoms: Non-custom, non-delux & non-Greenbriers. These used the "plush" foam in 1 1/4", we've increased that to 1 1/2". You can also move up to the "firm" foam if you want. Don't forget the cotton.Bench Seats & 4 Dr Rear Seats: Please check your seats to see how they were constructed. Comes in sheets 1= 24" x 66" they're bulky & do not compress very much. Weights vary depending on quantities ordered & packing required. Ultra Plush: 1" (seat backs only) C13177 4 lbs. Sample: C13177A Plush: 1 1/2" (seat bottoms) C13178 6 lbs. Sample: C13178A Firm: 1 1/2" (seat bottoms) C13179 6 lbs. Sample: C13179A Extra Firm: 1 1/2" (seat bottoms) C13180 6 lbs. Sample: C13180ANon-Cotton: This is a synthetic material that is not quite as dense as cotton, but "stays together" better than cotton. You may want to use several layers instead of the cotton, but note that it is NOT as firm as cotton, but does have slightly better "memor y". The 1/2 " is slightly denser & very useful for bucket seat cotton replacement on top of the seat buns as it stays together & stays put better than cotton. Note: Each non-bucket seat needs approx 55-66" & may need double layers. When you measure, allow 2-3" of overhang on each end. Non-Cotton 1/2" (slightly denser) 1 = 27" x 1 yd C13220 1 lb./yd Sample: C13220A Non-Cotton 3/4" 1 = 27" x 1 yd C13221 10 oz./yd Sample: C13221A Non-Cotton 2" 1 = 30" x 1 yd C13223 1 lb./yd Sample: C13223A 7/16" (semi-firm foam) 1 = 24" x 54" 2 = 24" x 108" C13085 3 lbs. /yd Sample: C13086Padding: Many seats used an "under padding", that was under the cotton layer and usually on top of the burlap. It might be dense cotton with burlap (or another mesh glued on) or it may be a jute-like material or even a dense felt material. You may choose to glue together several layers of cotton & a layer of burlap, or use 1 or 2 layers of our dense padding or even 1 or 2 layers of carpet padding or the 1/4 " jute. We suggest you get our full sample kit below so you can decide. See 3M glue bottom of page 265A. PADDING: These are some of our products that you may want to use to replace the "under padding". Also see Felt. Note: Each non-bucket seat needs approx 55-66" & may need double layers; when you measure allow 2-3" of overhang on each end. Dense Pad: Non-Cotton 3/4" 1 = 27" x 1 yd C13224 1 lb./yd Sample: C13224A Carpet Padding: 1/2" - sold by the yard 1 = 36" x 1 yd 2 = 36" x 2 yds., etc. C3801 3 lbs./yd. (most seats need Sample: C3801A 55-66" per layer) Felt: Felt was used in various places on some seats. Bucket seats and other seats had some 1/8" felt glued to the frame to cushion the upholstery that might rub against it. Bucket seats & other seats had 1/4 " felt hog ringed & hanging in the seat or between springs. It is often musty or torn. Several layers of 1/4 " can be glued together to produce a replacement for jute or felt "under padding". Note: Each non-bucket seat needs approx 55-66" & may need double layers. 1 / 8" Felt (approx thickness) 1 = 36" x 1 yd C13225 10 oz. /yd Sample: C13225A 1/4" Felt 1 = 40" x 1 yd C13226 1 lb./yd Sample: C13226ASET: Cotton, Burlap, Non-Cotton - Dense Padding, Felt, etc. You will receive samples of ALL of our materials (including paper covered wire) along with additional hints & info on how to fully restore your seats. Order C1445C - FREE with a par ts order. If ordering just the samples we do have to charge for shipping.SET: Foam. Mostly used for FC's & 4 doors. You will get a small sample of each of the 4 foams listed below. It is easier to tell the difference when you have a square foot of material but we cannot send that much. We will include hints to help you tell the differences & what to expect if you use that foam. Order C2825F - FREE with a parts order. If ordering just the foam samples we do have to charge for shipping.2 pieces approx 44 lbs., 3 pieces approx. 59 lbs. due to size. We pack as economically as possible to save you money on shipping.Note: For firm or extra firm, we suggest a layer of regular burlap on top & pulled snuggly over the foam - it helps it to wrap around front & sides.265BC13175C13175