Clark's Corvair Parts, Inc. - Corvair Parts Catalog - Over 12,000 parts

WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**

189

'60-64 CAR BODY PANELS

1960-64 REAR PANEL

PARTIAL REAR PANEL – FIBERGLASS

Behind bumper and down over to seams. Forms hole for air grill – below dots in sketch.

C1530X 8 lbs.

WHOLE REAR PANEL – FIBERGLASS

Replaces whole original rear panel from seams thru taillights and engine lid to

and including air grill area. Exhaust hole must be cut for Turbo. C1530F-U 68 lbs.

STEEL TRUNK BOTTOMS

Fix that rusted trunk – easily! These excellent repro panels go up about 3" on the sides and have all the

original reinforced ribs. You'll only ﬁnd 3 slight changes from the originals.

(1) The drain holes have been stamped but not cut thru.

(2) The "seam" across the 61-64 is simulated – not an overlapped moisture trap like the original.

(3) To avoid prohibitively costly tooling small cuts are made in the corners prior to stamping.

They can easily be welded closed during installation.

STEEL 61-64 Cars C4778A 8 lbs.

Also see FLOOR KITS – page 190

STEEL BATTERY BOX –

1961-64 (exc. Wagons)

YES! (Excuse sketch) Replace that rusted out battery box. Slightly thicker than original. All

welded and ready to be welded or pop riveted in. Includes approximately 1" extra in areas "C"

which allows you to heat and bend over in case the areas beside box are rusted. Top is left

straight with enough steel to form to gutter. Loop "A" is included. Bracket "B" is available or

use your original. (our bracket is not that original.)

BATTERY BOX C4361 5 lbs.

BRACKET "B" C4361B 8 oz.

ENGINE COMPARTMENT PATCH PANELS 1961-64 Cars

These panels allow you to easily patch two of the frequently rusted plastic plug holes. The 2” round Holes

(C4227 plugs) are used on nearly all models above the spare tire & battery box. The oblong (C4226 plugs) are in

common rust area of 62-64 convertibles – made from 20 ga steel – 5” x 5” these holes are exact for the plugs.

2” Round patch C3450 1 lb.

Oval patch C3451 1 lb.

Rain Gutter – Steel '61-64

ENGINE COMPARTMENT: Either Side above battery and spare tire.

Goes 1" into fender. 3 Ft. length. Order 2 pieces and do both sides.

Must be heated to bend slightly as installing.

C4780 2 lbs.

(Air= 5 Lbs.)

1964 ENGINE SKID PLATE END COVER: Repro of this hard to ﬁnd part.

Also needed for 61-63 A/C Cars C11943 1 lb.

TUNNEL PANS – STEEL

NOT EXACT but extremely close reproduction. Will get past all but the sharpest concours judge.

LONG ONE: 1960-64 C4781 9 lbs.

SHORT ONE: 1960-64 C1189R 2 lbs.

TUNNEL PAN INSULATOR SQUARE OF FELT: 2-3 were glued to the inside of 1960-69 tunnel

pans to keep cables and rods from rattling. Exact replacement.

1960-64 C718 4 oz.

PANEL DISCOUNT

page 186

iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**189'60-64 CAR BODY PANELS1960-64 REAR PANEL PARTIAL REAR PANEL - FIBERGLASS Behind bumper and down over to seams. Forms hole for air grill - below dots in sketch. C1530X 8 lbs. WHOLE REAR PANEL - FIBERGLASS Replaces whole original rear panel from seams thru taillights and engine lid to and including air grill area. Exhaust hole must be cut for Turbo. C1530F-U 68 lbs.STEEL TRUNK BOTTOMSFix that rusted trunk - easily! These excellent repro panels go up about 3" on the sides and have all the original reinforced ribs. You'll only find 3 slight changes from the originals. (1) The drain holes have been stamped but not cut thru. (2) The "seam" across the 61-64 is simulated - not an overlapped moisture trap like the original. (3) To avoid prohibitively costly tooling small cuts are made in the corners prior to stamping. They can easily be welded closed during installation. STEEL 61-64 Cars C4778A 8 lbs. Also see FLOOR KITS - page 190STEEL BATTERY BOX - 1961-64 (exc. Wagons)YES! (Excuse sketch) Replace that rusted out battery box. Slightly thicker than original. All welded and ready to be welded or pop riveted in. Includes approximately 1" extra in areas "C" which allows you to heat and bend over in case the areas beside box are rusted. Top is left straight with enough steel to form to gutter. Loop "A" is included. Bracket "B" is available or use your original. (our bracket is not that original.) BATTERY BOX C4361 5 lbs. BRACKET "B" C4361B 8 oz.ENGINE COMPARTMENT PATCH PANELS 1961-64 CarsThese panels allow you to easily patch two of the frequently rusted plastic plug holes. The 2" round Holes (C4227 plugs) are used on nearly all models above the spare tire & battery box. The oblong (C4226 plugs) are in common rust area of 62-64 convertibles - made from 20 ga steel - 5" x 5" these holes are exact for the plugs. 2" Round patch C3450 1 lb. Oval patch C3451 1 lb.Rain Gutter - Steel '61-64ENGINE COMPARTMENT: Either Side above battery and spare tire. Goes 1" into fender. 3 Ft. length. Order 2 pieces and do both sides. Must be heated to bend slightly as installing. C4780 2 lbs. (Air= 5 Lbs.)1964 ENGINE SKID PLATE END COVER: Repro of this hard to find part.Also needed for 61-63 A/C Cars C11943 1 lb.TUNNEL PANS - STEELNOT EXACT but extremely close reproduction. Will get past all but the sharpest concours judge. LONG ONE: 1960-64 C4781 9 lbs. SHORT ONE: 1960-64 C1189R 2 lbs. TUNNEL PAN INSULATOR SQUARE OF FELT: 2-3 were glued to the inside of 1960-69 tunnel pans to keep cables and rods from rattling. Exact replacement. 1960-64 C718 4 oz.PANEL DISCOUNTpage 186