Corvair Parts Catalog Corvair Engine Block Diagram, Engine Parts pg 9

WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**

Engine

Block

SHROUD BOLTS – All Year Corvairs

Order extras so you have them when needed. Also see page 8.

1/4” DIAMETER WASHER HEAD – plated, used in several places on the top shroud and Iower thermostat shroud,

muffler heat shields (sold Set of 10) C2121 6 oz./set

3/8” LARGE WASHER HEAD BOLT – used for edges of top shroud. Holds heater hose ducts to heads and other shrouds

at other end of heads, plated. (sold Set of 10) C2122 8 oz./set

WASHER HEAD SHEET SCREW – (2) sizes used on most engines in various places for shrouds (upper and lower) – (sold Set of 10)

Smaller Original Size (#8) Screws C2124A 2 oz./set

Larger Original Size (#10) Screws C2124 2 oz./set

OVERSIZE FOR STRIPPED ORIGINALS – If Original Size is C2124A – for OVERSIZE, USE C2124 2 oz./set

If Original Size is C2124 – for OVERSIZE, USE (#12 screws) C2125 2 oz./set

CLIP FOR SHEET METAL – Used in several places on rear shrouds, below oil cooler, etc. 1960-69 – Gives you something to “screw into”.

Available in 2 sizes: Larger usually for front & rear shroud retainers (60-64). “1” = Set of 10 (both for #10

screws) 5/8” x 7/16” C2128 2 oz. 3/4” x ½” C2128L 2 oz.

HEX HEAD WASHER MACHINE SCREW – Self-tapping. This is it! The one you lose and then try to force in a sheet metal screw. This is

used in numerous places. Goes into little nuts welded to shrouds, also those 3 where heater hose adaptor

attaches to shroud. “1” = Set of 10 Original Size C2126 2 oz./set OVERSIZE C2127 2 oz./set

SHROUD BOLTS – mixed – Set of 21. 3 of each bolt and screw (including oversize) listed above. Gives you a good selection but is

NOT ENOUGH for a full engine. C6171 6 oz./set

Rubber Engine Seal Retainer Screws – These original repros not in any sets

1965 Screws: Most were not "top hat" style. These are a good repro (black oxide like the originals),

screw and small washer. Individual Screw C3400C ½ oz. ea.

Full Set of 28 (includes one extra) C3400CR 6 oz.

1966-69 "Top Hat" Screws: These black oxide screws were used to attach the engine rubber seal to

the body. Ours are nearly exact repros, but the built in washer is slightly thinner and they do not have the small

letter stamped on the top. Individual Screw C3400L ½ oz. ea.

Full Set of 28 (includes one extra) C3400R 6 oz.

C3400L

C3400C

iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**9Engine BlockSHROUD BOLTS - All Year Corvairs Order extras so you have them when needed. Also see page 8.1/4" DIAMETER WASHER HEAD - plated, used in several places on the top shroud and Iower thermostat shroud, muffler heat shields (sold Set of 10) C2121 6 oz./set 3/8" LARGE WASHER HEAD BOLT - used for edges of top shroud. Holds heater hose ducts to heads and other shrouds at other end of heads, plated. (sold Set of 10) C2122 8 oz./set WASHER HEAD SHEET SCREW - (2) sizes used on most engines in various places for shrouds (upper and lower) - (sold Set of 10) Smaller Original Size (#8) Screws C2124A 2 oz./set Larger Original Size (#10) Screws C2124 2 oz./set OVERSIZE FOR STRIPPED ORIGINALS - If Original Size is C2124A - for OVERSIZE, USE C2124 2 oz./set If Original Size is C2124 - for OVERSIZE, USE (#12 screws) C2125 2 oz./set CLIP FOR SHEET METAL - Used in several places on rear shrouds, below oil cooler, etc. 1960-69 - Gives you something to "screw into". Available in 2 sizes: Larger usually for front & rear shroud retainers (60-64). "1" = Set of 10 (both for #10 screws) 5/8" x 7/16" C2128 2 oz. 3/4" x 1/2 " C2128L 2 oz. HEX HEAD WASHER MACHINE SCREW - Self-tapping. This is it! The one you lose and then try to force in a sheet metal screw. This is used in numerous places. Goes into little nuts welded to shrouds, also those 3 where heater hose adaptor attaches to shroud. "1" = Set of 10 Original Size C2126 2 oz./set OVERSIZE C2127 2 oz./set SHROUD BOLTS - mixed - Set of 21. 3 of each bolt and screw (including oversize) listed above. Gives you a good selection but is NOT ENOUGH for a full engine. C6171 6 oz./set Rubber Engine Seal Retainer Screws - These original repros not in any sets 1965 Screws: Most were not "top hat" style. These are a good repro (black oxide like the originals), screw and small washer. Individual Screw C3400C 1/2 oz. ea. Full Set of 28 (includes one extra) C3400CR 6 oz. 1966-69 "Top Hat" Screws: These black oxide screws were used to attach the engine rubber seal to the body. Ours are nearly exact repros, but the built in washer is slightly thinner and they do not have the small letter stamped on the top. Individual Screw C3400L 1/2 oz. ea. Full Set of 28 (includes one extra) C3400R 6 oz.C3400LC3400C