Corvair Parts Catalog Electric Fuel Pump Conversion Kits pg 66

WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**

Electric Fuel Pump Kits: All 1960–69 Corvairs

Order just one part number and know that you've got everything you need to install the electric fuel pump. Separate parts follow.

Basic Kit: Electric pump and filter, installation kit, oil pressure safety switch. C10294 2 lbs.

Ultimate Kit: Same as BASIC KIT but includes both the inertia & oil pressure style safety switches. C10295 3 lbs.

Electric Fuel Pumps Top Quality — 100% solid state — Quietest Pump

Lasts longer than regular pumps. Much less affected by vapor lock. Water tight and corrosion resistant. Built in

pressure relief for less chance of flooding. Also see Safety Switch and Installation Kit. The safety switch must be

added so it stops the pump if engine "dies". C5606 2 lbs.

** Installation Kit – Suggested: Includes necessary parts and instructions, as well as plug below. Also order

SAF ETY SWITCH. C5607 6 oz.

Replacement Filter: For electric pump C5606F 8 oz.

Fuel Pump Plug: Included in KITS and Installation Kit. Machined aluminum plug replaces stock fuel pump when electric

pump is used. Comes with VITON o-ring. C5406 4 oz.

Safety Shut Off Switch: THIS IS A MUST!

It should shut off the electric pump if you have an accident in case there is a gas leak. The OIL PRESSURE STYLE has been used for years and shuts off

power to the pump if oil pressure drops (engine stops). No matter why the engine stops, the pump will stop. However, you could have an accident with

a fuel leak and the engine still be running. The INERTIA SWITCH will shut of f power to the pump if it senses an abrupt stop (as in an accident). The pump

will be shut off even if the engine stays running. (The switch has a reset). However, this inertia switch has a draw back. If your engine should stall while

you've left it running, the pump can still keep running and could possibly flood out your engine with fuel. The Best? Install one of each type in series.

Then either one can shut of f the pump depending on the situation. Both come with instructions and needed installation parts.

Oil Pressure Shut Off Switch C5607X 10 oz.

Inertia Type Shut Off Switch C9848 1 lb.

Fuel Pump By-Pass Plate

This replaces the center of your fuel pump when using an electric pump so the fuel goes straight through; won't leak & looks very

close to stock. Use your old fittings or order new ones from page 65. Fits all Corvair fuel pumps & comes with instructions.

C12879 8 oz.

Gas Tank Sealers – even seal NEW TANKS!

We now offer 2 types of Gas Tank Sealers. Both types require that the tank be removed, cleaned & dried completely.

We've used both with excellent results. We've sold the "original" since 1990 & The "BEST" since 1999.

Gas Tank Sealer Hint: We've found it works best to rotate the tank about every 5 minutes for 30 minutes.

This gives a complete thick coating if you are doing just one coat.

Gas Tank Sealer: Original

It is resistant to all alcohol blended fuels and adheres even tighter to metal and rust. It remains flexible and stays on even if the tank is dented. If tank has extreme rust, have

it professionally cleaned. If tank has minor rust, just dr y and seal. Tank must be removed. Allow a minimum of 2 days to dry. Do not use rust preservers in tank first. 1 can

will seal a car or FC tank with 2 coats. We highly suggest you seal your NEW tank. Sold in Quar ts. C9390 3 lbs. (NO Air Shipping)

Gas Tank Sealer: "The BEST" by Por-15

This product is made by POR-15 and is highly resistant to all current fuels including higher alcohol and all additives and solvents.

This sealer is non-flammable and environmentally safe while it chemically bonds to the inside of your dry gas tank (new or used).

NOTE: For best results, clean tank with "MARINE CLEAN" and then etch with "METAL READY". These 3 products have been designed

to work together to give the best, most durable gas tank coating possible. One quart will easily double coat a Corvair tank (car or FC).

Instructions included. Allow a minimum of 3 days to dry. C11133 3 lbs. (NO Air Shipping)

Ultimate Gas Tank Kit – This is it! By Por-15

You get the following:

• 2 quarts of Marine Clean (removes gum, sludge and varnish)

• Prep-Ready (removes minor rust and etches bare metal)

• 1 quart of "The Best" Gas Tank Sealer

PLUS, complete instructions for doing a perfect job.

Ultimate Gas Tank Kit C11134 15 lbs. (NO Air Shipping)

ENGINE DISCOUNT !

see Blue pg. MK-2

Filter

Pump

ENGINE REBUILDS engine rebuilds

The PISTONS, VALVES & RINGS are the most important parts in an engine rebuild. CLARK PISTONS are the best available and all take

original style Corvair rings. These were fully retooled and engineered in 2000 to give us SUPERIOR ENGINE PARTS.

iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**66Electric Fuel Pump Kits: All 1960-69 CorvairsOrder just one part number and know that you've got everything you need to install the electric fuel pump. Separate parts follow.Basic Kit: Electric pump and filter, installation kit, oil pressure safety switch. C10294 2 lbs.Ultimate Kit: Same as BASIC KIT but includes both the inertia & oil pressure style safety switches. C10295 3 lbs.Electric Fuel Pumps Top Quality -- 100% solid state -- Quietest PumpLasts longer than regular pumps. Much less affected by vapor lock. Water tight and corrosion resistant. Built in pressure relief for less chance of flooding. Also see Safety Switch and Installation Kit. The safety switch must be added so it stops the pump if engine "dies". C5606 2 lbs.** Installation Kit - Suggested: Includes necessary parts and instructions, as well as plug below. Also order SAF ETY SWITCH. C5607 6 oz.Replacement Filter: For electric pump C5606F 8 oz.Fuel Pump Plug: Included in KITS and Installation Kit. Machined aluminum plug replaces stock fuel pump when electric pump is used. Comes with VITON o-ring. C5406 4 oz.Safety Shut Off Switch: THIS IS A MUST!It should shut off the electric pump if you have an accident in case there is a gas leak. The OIL PRESSURE STYLE has been used for years and shuts off power to the pump if oil pressure drops (engine stops). No matter why the engine stops, the pump will stop. However, you could have an accident with a fuel leak and the engine still be running. The INERTIA SWITCH will shut of f power to the pump if it senses an abrupt stop (as in an accident). The pump will be shut off even if the engine stays running. (The switch has a reset). However, this inertia switch has a draw back. If your engine should stall while you've left it running, the pump can still keep running and could possibly flood out your engine with fuel. The Best? Install one of each type in series. Then either one can shut of f the pump depending on the situation. Both come with instructions and needed installation parts. Oil Pressure Shut Off Switch C5607X 10 oz. Inertia Type Shut Off Switch C9848 1 lb.Fuel Pump By-Pass PlateThis replaces the center of your fuel pump when using an electric pump so the fuel goes straight through; won't leak & looks very close to stock. Use your old fittings or order new ones from page 65. Fits all Corvair fuel pumps & comes with instructions. C12879 8 oz.Gas Tank Sealers - even seal NEW TANKS!We now offer 2 types of Gas Tank Sealers. Both types require that the tank be removed, cleaned & dried completely. We've used both with excellent results. We've sold the "original" since 1990 & The "BEST" since 1999.Gas Tank Sealer Hint: We've found it works best to rotate the tank about every 5 minutes for 30 minutes.This gives a complete thick coating if you are doing just one coat.Gas Tank Sealer: OriginalIt is resistant to all alcohol blended fuels and adheres even tighter to metal and rust. It remains flexible and stays on even if the tank is dented. If tank has extreme rust, have it professionally cleaned. If tank has minor rust, just dr y and seal. Tank must be removed. Allow a minimum of 2 days to dry. Do not use rust preservers in tank first. 1 can will seal a car or FC tank with 2 coats. We highly suggest you seal your NEW tank. Sold in Quar ts. C9390 3 lbs. (NO Air Shipping)Gas Tank Sealer: "The BEST" by Por-15This product is made by POR-15 and is highly resistant to all current fuels including higher alcohol and all additives and solvents. This sealer is non-flammable and environmentally safe while it chemically bonds to the inside of your dry gas tank (new or used). NOTE: For best results, clean tank with "MARINE CLEAN" and then etch with "METAL READY". These 3 products have been designed to work together to give the best, most durable gas tank coating possible. One quart will easily double coat a Corvair tank (car or FC). Instructions included. Allow a minimum of 3 days to dry. C11133 3 lbs. (NO Air Shipping)Ultimate Gas Tank Kit - This is it! By Por-15You get the following: o 2 quarts of Marine Clean (removes gum, sludge and varnish) o Prep-Ready (removes minor rust and etches bare metal) o 1 quart of "The Best" Gas Tank Sealer PLUS, complete instructions for doing a perfect job.Ultimate Gas Tank Kit C11134 15 lbs. (NO Air Shipping)ENGINE DISCOUNT !see Blue pg. MK-2FilterPumpENGINE REBUILDS engine rebuilds The PISTONS, VALVES & RINGS are the most important parts in an engine rebuild. CLARK PISTONS are the best available and all take original style Corvair rings. These were fully retooled and engineered in 2000 to give us SUPERIOR ENGINE PARTS.