Home | Order Catalog | Online Catalog | New Items | Contact Us |
![]() |
![]() |
![]() |
![]() |
|
![]() |
![]() i WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov** 167B Performance Nylon Bushings C2051P C2050P A complete performance bushing. Self-lubricating black MDS (molybdenum disulfide) filled bushing with center sleeve & aluminum shell (on most). Just remove your old stock bushing and replace with these. Front Upper A-Arm (Set of 4) does both sides Front Lower A-Arm Cars = Set/2; FC = Set/4 (does both sides) Rear Lower A-Arm (Set of 4) does both sides 60-64 Cars C1665EP 1 lb. C1664P 12 oz. C3070P 2 lbs. 61-65 FC C4907P 2 lbs. C3070P 2 lbs. C3070P 2 lbs. 65-69 Cars C1665LP 1 lb. C957P 12 oz. - - - - - - - - - - - Front Stabilizer Center Link Nylon Bushings: Set of 2 upper & 2 lower Bushings. No sleeves (use stock sleeves). We suggest stock rubber for outer end bushings. 1962-63 with stock bars C111EP 4 oz./set 1964-69 with stock bars C111P 4 oz./set 1965-69 Rear Strut Rod Bushings: 2-piece bushings with machined "stops" at each end for easier installation. One set includes (2) 2-piece bushings and 2 new serrated sleeves. One set is enough for one strut rod; order 2 sets to do both strut rods. C1899P 1 lb./set 1965-69 Torque Arm Bushings One set does both sides. Nylon and aluminum. C2051P 1 lb./set 1965-69 Upper Transmission Crossmember Bushings 2 new nylon bushings, new sleeves & new aluminum shells. Enough for both sides. C2050P 1 lb. 8 oz./set "MONOBALL" REAR TORQUE ARM ASSEMBLIES These bearing units replace the original rubber bushings at the front end & will lead to a stiffer but more controlled ride. NOTE: you must weld them in place and if you decide to go back to original, it will require some work so consider carefully before making your decision. Come with complete instructions & hardware for both sides. Set of Monoballs C2826 4 lbs. LOWER CONTROL ARM BRACKET Lowers attaching point for rear control arm (under drive shafts) so wheels move more nearly paraIlel. C5118 5 lbs. STABILIZER BARS – EARLY CARS & VANS Add a front or rear stabilizer bar to your Car or Van for added control and handling fun. Each bar includes complete hardware and step by step instructions. For Vans, Greenbriers, & Rampsides – direct bolt on, perfect fit and greatly improves handling. Year Front Rear 1960-64 Cars C6045 15 lbs. C2306R 16 lbs. 1965-69 Cars Discontinued C2308R 30 lbs. 1961-65 Vans C5067 25 lbs. C5068 25 lbs. Finally a bar that fits and is quite easy to install. The main bar is 3/4" diameter, which most consider a good all around rear bar diameter. Prototype was used in over 50 races including Watkins Glen. Includes all hardware & instructions. No welding required, but you must drill some holes. Large rubber bushings & heim joints are used to connect bar to the body brackets. Little or no decrease in ground clearance. C2308R 16 lbs. Replacement Crown Stabilizer Bar Bushings – Small Grommet: 8 needed for rear & 8 needed for front. Set of 4 C376 6 oz./set Individual C396 2 oz. ea. 1965-69 Rear Stabilizer Bar C2826 C1899P ![]() |
Next![]() |
Search In Corvair Catalog Content
|
CLARKS- MORE THAN PARTS. |
![]() |
What's New |
Clark's History |
Corvair History |
Contact Us |
Customer Service |
Technical Service |
Change of Address
Order Catalog | Catalog Indexes | Technical Tips | Corvair Power | Engine Worksheet | Interior Worksheet | Parts We Buy | Cars, Buy or Sell Order Forms: Parts | Gift Certificates | Ordering Policies | Shipping Charges |
![]() |
![]() Copyright © 1978, 2019 Clark's Corvair Parts, Inc., "Clark's Corvair Parts" and the "Corvair Map" are registered service marks of Clark's Corvair Parts, Inc. 400 Mohawk Trail Shelburne Falls, MA 01370 USA All rights reserved. Main Office Phone: 413.625.9776 Fax: 413.625.8498 |