Corvair Parts Catalog FC Accelerator Cables pg 73

WARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**

Van Accelerator Linkage

Accelerator Cable Note: 1961 – through about Feb 1961 used the "1st design" cable which stopped at the differential pivot.

We believe the rest of the 1961–65 all used the cable that ended at the carb cross shaft. Over the years, some "1st Design"

FC were switched to the later style. Check yours before ordering! Check photo captions!

1. Washer: Sold set of 2. C4584 1 oz./set

2. Fiber Washers: Above and below seal. Sold set of 2. C797A 2 oz./set

3. Felt Seal: Accelerator through floor. C797 2 oz.

4. Accelerator Pedal: May vary slightly from original (check availability).

Exact Repro 1961–63 C795 1 lb.

1964–65 C4955 1 lb.

5. Screw : Special for accelerator pedal. Sold set of 2.

Exact Original clutch head C4585C 2 oz./set

Usable replacement slotted head C4585 2 oz. /set

6. Cotter Pin C4586 1 oz.

7. Pivot Pin 1961–63 C799 4 oz.

7½. Front Accelerator Cable Return Spring (Carb return spring see #23)

1961 First Design Accelerator (Manual & PG) – 5½" C1235 4 oz.

1961-65 ALL with Cable to Carb Cross Shaft – 3½" C499 4 oz.

7¾. Cotter Pin: Some years used this through the front valance panel & the spring went through

the cotter pin eye. C1235C 1 oz.

8. Lever: Holes often wear. 1961–63 CX1629 8 oz.

8½. "E" Clip: Sold set of 2. (some used COT TER PIN) C727L 1 oz./set

9. Cotter Pin : Front cable C4587 1 oz.

Set of 5 C726A 1 oz./set

10. Washer: Front cable. C7332 1 oz.

11. Accelerator Cable: See note at top about "1st Design". If your cable is old, consider carrying

a spare or replacing.

1961 "1st Design" Accel Cable (ends at differential pivot) C794E 2 lbs.

1961–65 Accelerator Cable (ends at carb cross shaft) C794L 2 lbs.

12. Retainer Clip C3787 1 oz.

13. Adjusting Swivel C2257 2 oz.

14. Adjusting Rod C2254 4 oz.

15. Adjusting Keeper C2255 1 oz.

16. Screw for Keeper C2256 1 oz.

17. Nylon Sleeve C549 1 oz.

18. Rubber Bushing C547 1 oz.

19. Special Washer: Sold set of 2. C549W 1 oz./set

20. "C" Clip: Sold set of 5. C727 1 oz./set

21. Special Washers: Throttle pivot shaft. Sold set of 2. C727W 1 oz./set

22. Set of 3 Attaching Bolts with Lock Washers C11016 4 oz./set

23. Return Spring at Carb (cross shaft)

1961 1st Design Accel. (manual & PG) C1237 4 oz.

1961–65 with Cable to Carb Cross Shaft (exc. PG) C499 4 oz.

1961–65 PG with Cable to Carb Cross Shaft C1237 4 oz.

24. Swivel C552 2 oz.

PICTURE #

These were originally a bronze bushing

Part of

Accelerator

Cable

NOTE: If your FC had a throttle

rod into engine and now you use

a cable – the rod hole can

be plugged with C4227 2 oz.

C795

iWARNING: Products on this page can expose you to a chemical, which is known to the St ate of California to cause cancer or reproductive harm. **For more information go to www.P65Warnings.ca.gov**73Van Accelerator LinkageAccelerator Cable Note: 1961 - through about Feb 1961 used the "1st design" cable which stopped at the differential pivot. We believe the rest of the 1961-65 all used the cable that ended at the carb cross shaft. Over the years, some "1st Design" FC were switched to the later style. Check yours before ordering! Check photo captions!1. Washer: Sold set of 2. C4584 1 oz./set 2. Fiber Washers: Above and below seal. Sold set of 2. C797A 2 oz./set 3. Felt Seal: Accelerator through floor. C797 2 oz. 4. Accelerator Pedal: May vary slightly from original (check availability). Exact Repro 1961-63 C795 1 lb. 1964-65 C4955 1 lb.5. Screw : Special for accelerator pedal. Sold set of 2. Exact Original clutch head C4585C 2 oz./set Usable replacement slotted head C4585 2 oz. /set 6. Cotter Pin C4586 1 oz.7. Pivot Pin 1961-63 C799 4 oz.7 1/2 . Front Accelerator Cable Return Spring (Carb return spring see #23) 1961 First Design Accelerator (Manual & PG) - 5 1/2 " C1235 4 oz. 1961-65 ALL with Cable to Carb Cross Shaft - 3 1/2 " C499 4 oz.7 3/4 . Cotter Pin: Some years used this through the front valance panel & the spring went through the cotter pin eye. C1235C 1 oz.8. Lever: Holes often wear. 1961-63 CX1629 8 oz. 8 1/2 . "E" Clip: Sold set of 2. (some used COT TER PIN) C727L 1 oz./set 9. Cotter Pin : Front cable C4587 1 oz. Set of 5 C726A 1 oz./set 10. Washer: Front cable. C7332 1 oz.11. Accelerator Cable: See note at top about "1st Design". If your cable is old, consider carrying a spare or replacing. 1961 "1st Design" Accel Cable (ends at differential pivot) C794E 2 lbs. 1961-65 Accelerator Cable (ends at carb cross shaft) C794L 2 lbs.12. Retainer Clip C3787 1 oz.13. Adjusting Swivel C2257 2 oz.14. Adjusting Rod C2254 4 oz.15. Adjusting Keeper C2255 1 oz. 16. Screw for Keeper C2256 1 oz.17. Nylon Sleeve C549 1 oz.18. Rubber Bushing C547 1 oz.19. Special Washer: Sold set of 2. C549W 1 oz./set20. "C" Clip: Sold set of 5. C727 1 oz./set21. Special Washers: Throttle pivot shaft. Sold set of 2. C727W 1 oz./set22. Set of 3 Attaching Bolts with Lock Washers C11016 4 oz./set23. Return Spring at Carb (cross shaft) 1961 1st Design Accel. (manual & PG) C1237 4 oz. 1961-65 with Cable to Carb Cross Shaft (exc. PG) C499 4 oz. 1961-65 PG with Cable to Carb Cross Shaft C1237 4 oz.24. Swivel C552 2 oz.PICTURE #These were originally a bronze bushingPart of Accelerator CableNOTE: If your FC had a throttle rod into engine and now you use a cable - the rod hole canbe plugged with C4227 2 oz. C795